Retrofitting E-Lockers into a 92LC

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 14, 2009
Threads
9
Messages
58
Location
Ohio
Ok, so now that I scored complete locking axles from a donor 95LC, does anyone know how much of the needed wiring is actually already in a 1992 LC? I took every wire that I could find off of the 95 from the fuse box all the way to the tail lights. Yes I have the locker ECU and the switch. I took this out with the complete loom under the dash board. I did not take the wires between the back tail lights. So pretty much every electrical wire on the vehicle I have.

I think the 1992 LC over seas with the diesel motors were offered with lockers. Can anyone confirm this?

If so what wiring is already inside of my vehicle that I can connect to?

Any help is appreciated. Thanks, Rick
 
Hey Taco 162 - I've done the swap into my '92 HDJ81. Luckily you have the full axle assemblies.

Lockers were an option in JDM's => all years. Thats why mine came with the locker plug just above the rear LHS frame rail. Check if your NA spec came with it. Not sure.

If not, no biggie - pull your jack and splice into the harness there.

Front is plug and play.
 
Hey Taco 162 - I've done the swap into my '92 HDJ81. Luckily you have the full axle assemblies.

Lockers were an option in JDM's => all years. Thats why mine came with the locker plug just above the rear LHS frame rail. Check if your NA spec came with it. Not sure.

If not, no biggie - pull your jack and splice into the harness there.

Front is plug and play.
I know this is an old thread so i hope you are still on here!
So i recently bought a 93 JDM HDJ81 without lockers. I'm trying to decide if I should fork out $1200+ for an ARB or Harrop Elocker, or buy a full rear axle assembly for waaaaaay cheaper. I have a couple of questions if you don't mind...........
Is it a pretty straight forward swap from a 91-97 north American (NA) 80 series to my HDJ81? For now just going to do the rear.
Does my JDM HDJ81 have all of the wiring harnesses in place to just plug and play? I can see the illumination icons in my instrument cluster
Which wiring would I need off of the NA spec 80 for my JDM 81?

BTW and I'm sure you are aware, my new HDJ81 has rear disc brakes with auto transmission (if it matters)
Thank you so much
 
Hi - '93 is the best year. Yes, it's a straightforward swap on an HDJ81 as the sill, switch and computer wiring are already in place. From memory you will need the following from the donor:
- Front locker harness from diff to RH fender ---> existing connector near RH firewall
- Rear locker harness from diff to rear cross member ---> existing connector @ rear crossmember
- locker switch ---> existing connector behind dash blank
- locker ECU ---> existing connector @ kick panel
- 2 light bulbs for dash indicators (good time to pull reverse alarm)
- front and rear housings with axles, thirds and control arm wiring mounts (can substitute zip-ties)

The Harrops can be wired with the factory switch and indicator lights as well.
Note: The OEM front and rear locker harness (diff to frame) are now discontinued.
 
Hi - '93 is the best year. Yes, it's a straightforward swap on an HDJ81 as the sill, switch and computer wiring are already in place. From memory you will need the following from the donor:
- Front locker harness from diff to RH fender ---> existing connector near RH firewall
- Rear locker harness from diff to rear cross member ---> existing connector @ rear crossmember
- locker switch ---> existing connector behind dash blank
- locker ECU ---> existing connector @ kick panel
- 2 light bulbs for dash indicators (good time to pull reverse alarm)
- front and rear housings with axles, thirds and control arm wiring mounts (can substitute zip-ties)

The Harrops can be wired with the factory switch and indicator lights as well.
Note: The OEM front and rear locker harness (diff to frame) are now discontinued.
Awesome thank you so much! Stupid question though. I can do one at a time correct? Planning on doing rear first then front as funds allow
 
Yes, that's what I did and installed the front a year later. You will have to modify the front housing as the Panhard mount will be on the opposite side if it's from a LHD donor
 
Awesome thank you so much! Stupid question though. I can do one at a time correct? Planning on doing rear first then front as funds allow

As long as tou have the same ratio R&P‘s or a set of locking hubs upfront, yes. (Or lock the CDL & pull your FR driveline).

-Main thing is the driveline bind if you’re on 2 different R&P’s.

I think the diesels all got something like 3.73’s where the 1FZ was 4.10/4.11 (I forget which TBH).

Your door sticker will tell the drivetrain specs to decode your axles, but realize you may be lowering your ratio’s if you just stuff full 3rds or complete axles under your 80.
 
As long as tou have the same ratio R&P‘s or a set of locking hubs upfront, yes. (Or lock the CDL & pull your FR driveline).

-Main thing is the driveline bind if you’re on 2 different R&P’s.

I think the diesels all got something like 3.73’s where the 1FZ was 4.10/4.11 (I forget which TBH).

Your door sticker will tell the drivetrain specs to decode your axles, but realize you may be lowering your ratio’s if you just stuff full 3rds or complete axles under your 80.
I believe they are the same, 4.10 for auto trans.
 
Does anyone know which part number i need to order from Megazip or are all of these compatible?
8216582165-60020
Wire, Frame, No.2
[05.1993 - 01.1995] FZJ80,HDJ81,HZJ81..LUB
—SHOW
8216582165-60030
Wire, Frame, No.2
[05.1993 - 01.1995] FZJ80,HDJ81,HZJ81..LUB アリ(デフアレンシヤル ロツク)
US $125.46
SHOW
8216582165-60090
Wire, Frame, No.2
[08.1992 - 05.1993] FZJ80,HDJ81..VXL; FZJ80,HDJ81,HZJ81..GX,VX アリ(*66)
US $128.52
SHOW
replacement
82165-60101
Wire, Frame, No.2
[08.1992 - 05.1993] FZJ80,HDJ81..VXL; FZJ80,HDJ81,HZJ81..GX,VX アリ(*66)
US $128.52
there are 1 pc. in shopping cart
SHOW
8216582165-60100
Wire, Frame, No.2
[08.1992 - 05.1993] FZJ80,HDJ81..VXL アリ(デフアレンシヤル ロツク); FZJ80,HDJ81,HZJ81..GX,VX アリ(*66) & アリ(デイフアレンシヤル ロツク)
US $125.46
SHOW
 
Hi - '93 is the best year. Yes, it's a straightforward swap on an HDJ81 as the sill, switch and computer wiring are already in place. From memory you will need the following from the donor:
- Front locker harness from diff to RH fender ---> existing connector near RH firewall
- Rear locker harness from diff to rear cross member ---> existing connector @ rear crossmember
- locker switch ---> existing connector behind dash blank
- locker ECU ---> existing connector @ kick panel
- 2 light bulbs for dash indicators (good time to pull reverse alarm)
- front and rear housings with axles, thirds and control arm wiring mounts (can substitute zip-ties)

The Harrops can be wired with the factory switch and indicator lights as well.
Note: The OEM front and rear locker harness (diff to frame) are now discontinued.
Hey @SHREDwagon , is the rear axle and harness out of a 1997 Lexus LX450 compatible? Have an opportunity to pick one up for a killer price.
 
Hey @SHREDwagon, so I'm finding several locked rear axle assemblies out of US spec 80's but all of the harnesses have been cut instead of unplugged (idiots). What part numbers will work for the locker harness? Megazip shows several different numbers but I assume any of them will work? If I can't find a new harness, I'm just going to try and get one of the cut ones and just splice it back together. Shouldn't be too difficult. Part numbers are listed above in my previous post. Megazip says they have a couple of them in Japanese warehouse. Not sure if that's correct though
 
Back
Top Bottom