rear PHH coolant flow question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 14, 2002
Threads
88
Messages
1,228
Location
NW side of chicago
I am about to reroute the current heater hoses going to the back passenger seats. I am curious if the flow of coolant to the heater would be critical to operations. I am say this because the hoses goes behind the cats (untraceable without removal) and I am not sure if they get turned around or mixed up.Thanks for the input.
 
It's unclear what you are asking. Perhaps tell us what you intend/want to accomplish and ask if that's going to affect anything else? Also a hint on what the problem is causing you to do this?

DougM
 
I believe he's saying:
1. He wants to replace his rear heater lines. Since doing this with OEM metal lines requires dropping the tranny, he is likely using all rubber hose instead.
2. He can't see what the OEM lines do when they go behind the cats. They may cross-over one another and swap positions as far as supply & return go.
3. His question is - if the rear heater core is plumbed backwards (since he can't be sure about the supply & return) will this hurt anything?

Archie, am I close?

BTW, I would think it does not matter. If it were a fluid to fluid heat exchanger it would make an efficiency difference. A heater core just has air blowing across it, so fluid direction through it shouldn't matter. I'll let someone else confirm or debunk this.
 
I am about to reroute the current heater hoses going to the back passenger seats. I am curious if the flow of coolant to the heater would be critical to operations. I am say this because the hoses goes behind the cats (untraceable without removal) and I am not sure if they get turned around or mixed up.Thanks for the input.

1 goes in the heater core the other goes out. I cant see that any thing would be hurt by shutting them off like when you turn the heater valve off.
 
1 goes in the heater core the other goes out. I cant see that any thing would be hurt by shutting them off like when you turn the heater valve off.

I am also not sure what question is being asked,
but I will mention a couple of things;

In my FJ62, when my rear heater went bad, instead of replacing
it, I just put a small piece of hose between the two metal pipes, it recirculates the water back to the system.

If he is going to replace the metal pipes with rubber hose,
I would suggest at least a high temp silicone hose or even
a commerical grade cloth wrapped silicone hose if it
was to be routed near anything that could abrade it.

I have found the GATES makes a few different grades of high quality
heater hose; up to the cloth wrapped version that costs about 15 dollars a foot!!

g
 
Here is a thread that shows the rear heater lines in post #7:

https://forum.ih8mud.com/showthread.php?t=103712&highlight=cats+heater

The hard lines can be replaced by removing the cats and heat shields.

I am taking my rig to the exhaust guy in town to :

1. Rotate the cats 90 degrees and,
2. Put on non-permanent connectors on each end of the cat pipes so that I can disassemble them when I want to so that I can service these heater heater pipes.

Mine are rusted but not leaking (yet). I have used Film Oil undercoating to slow down the rusting (hope they last through the winter).

Questions:

What are the part numbers for these rear heater pipes?

How tough is it to get them off and new ones on?

:beer:
 
I believe he's saying:
1. He wants to replace his rear heater lines. Since doing this with OEM metal lines requires dropping the tranny, he is likely using all rubber hose instead.
2. He can't see what the OEM lines do when they go behind the cats. They may cross-over one another and swap positions as far as supply & return go.
3. His question is - if the rear heater core is plumbed backwards (since he can't be sure about the supply & return) will this hurt anything?

Archie, am I close?

BTW, I would think it does not matter. If it were a fluid to fluid heat exchanger it would make an efficiency difference. A heater core just has air blowing across it, so fluid direction through it shouldn't matter. I'll let someone else confirm or debunk this.

Yes, thanks for deciphering my question :). Sorry for being a little unclear.I didn't think the fluid flow mattered but just wanted to make sure.You never know if they have any anti backflow valves. I just recently thought of blowing compressed air in lines and see which one would spray fluid to reverify my connections. This way I'll be sure to connect it exactly in the same flow pattern. I am doing this repair right now so I typed it up without rereading it. Thanks again everybody for your response.
 
Here is a thread that shows the rear heater lines in post #7:

https://forum.ih8mud.com/showthread.php?t=103712&highlight=cats+heater

The hard lines can be replaced by removing the cats and heat shields.

I am taking my rig to the exhaust guy in town to :

1. Rotate the cats 90 degrees and,
2. Put on non-permanent connectors on each end of the cat pipes so that I can disassemble them when I want to so that I can service these heater heater pipes.

Mine are rusted but not leaking (yet). I have used Film Oil undercoating to slow down the rusting (hope they last through the winter).

Questions:

What are the part numbers for these rear heater pipes?

How tough is it to get them off and new ones on?

:beer:
I don't know to much about parts no.
The OEM prices that somebody on a previous thread mentioned was about 60
buck.
Most people bypass the original connections with 1/2 inch rubber heater hose and clamps.
Here's another thread with some description. https://forum.ih8mud.com/showthread.php?t=66618&highlight=coolant+hose+cat
I would reccommend anybody living in the rust belt be vigilant about these hoses because you won't be able to detect it easily in the puddles of winter.
The tools I used.
utility knife-to cut out old rubber hose that goes into the rear heater from the floor board.
dremel tool with wide cutoff wheel to cut through the old lines next to tranny. You can use a recipricating saw but might have to cut lower.
pan-to catch all the fluid
clamps
patience to wait for the fluid to drain out-be careful of electrical tools
zip ties- to tie hoses to the frame.
water based lubricant to fit the hoses on.
I used about 8 ft(4ft each line) of hose from the driveshaft/frame area to the heater connectors
Other things that could be used could be found in the real/original PHH threads-pliers,screwdrivers,etc....
Any other question while it's fresh on my mind?
 
A stubby screwdriver is also reccommended to tighten down the hose clamps.

Just to answer Jacques question about the difficulty. I would say it would be difficult to replace the line with OEM equipment. Since you are in Ontario (Canada, I believe, not California) I would replace the lines with OEM lines if you have the chance to remove the cats. Chances are your lines are only months or a year away from leaking. If they salt the roads and are exposed to harsh conditions then they will be corroded. I actually suspect that the lines are leaking from the brackets when the truck flexes and abrades the lines. I have seen this from my 88 LC where all the leaks started at the bracket holding down the lines.
Just to give you an idea of time involved. I started at 3pm. Planning my strategy, buying the supplies, going to hardware store for dremel cut-off wheel, quick groceries,dinner, write in MUD and it's 12 midnight. It seems easy but things generally take longer than expected.
 
A stubby screwdriver is also reccommended to tighten down the hose clamps.

Just to answer Jacques question about the difficulty. I would say it would be difficult to replace the line with OEM equipment. Since you are in Ontario (Canada, I believe, not California) I would replace the lines with OEM lines if you have the chance to remove the cats. Chances are your lines are only months or a year away from leaking. If they salt the roads and are exposed to harsh conditions then they will be corroded. I actually suspect that the lines are leaking from the brackets when the truck flexes and abrades the lines. I have seen this from my 88 LC where all the leaks started at the bracket holding down the lines.
Just to give you an idea of time involved. I started at 3pm. Planning my strategy, buying the supplies, going to hardware store for dremel cut-off wheel, quick groceries,dinner, write in MUD and it's 12 midnight. It seems easy but things generally take longer than expected.
Thanks for all the advice, archie ! :beer:

Driving around these parts in the winter is like being at a Siberian salt mine. I wand wash the truck as often as possible and undercoat it before the snow hits the fan.

Tomorrow, my rig is scheduled to have the cats removed, turned 90 degrees and placed back on with clamps that I can easily remove later. This way I can get to the metal tubing for the rear heater, that is rusting away, alot easier. I think I will ask the exhaust guy to see if he can loosen up the nuts holding on the heat shields too.

I believe beno said in his post (see a previous link) that the metal tubes were a b%#ch to get off.

I hope to preserve the rubber hoses. So what I plan to do is make sure I have all the new parts at hand, drain the coolant, carefully pry the rubber hoses off the ends of the metal tubing, lube the hose ends with a silcone based lubricant (that is supoosedly good for rubber) and hopefully the new tubes slip back on like a knife going through soft butter.

When that is all done, my SROR bumper may be ready to go and I just might order a set of those SROR rock sliders with bump outs. They look almost as good as ... well, you know, :princess:, wearing, well, you know ! Not much.:D
 
You're welcome. Another thing to add on the list of supplies is safety googles and baseball cap. Googles will keep the antifreeze,falling rust particles,dirt/dust, shattered cut off wheel, etc ... out of your eyes. I wear perscription glasses and stuff still fell into my eyes making it more annoying to remove particles out of the eyes with dirty hands coated with antifreeze. Rubber gloves would also help because the chemicals in the antifreeze messed up my skin. I rather have done a greasier job.
 
Back
Top Bottom