rear diff not locking. i have searched...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 4, 2009
Threads
88
Messages
598
Location
England
ok ive been searching for hours and now my eyes are hurting.

my rear diff is not locking. it used to lock and now it doesnt. i can hear the actuator engaging but the dash light still flashes. ive done figure of eights on gravel and the tyres dont "grab".

i had the front prop shaft off last week so i had the chance to engage the cdl and then engage the rear locker and do some tight turning on tarmac, still no diff lock action...

i havnt had the time to have a look at it yet. but before i start taking things apart any pointers?
 
You probably just need to work it a bit. Find some soft ground, put in low range, engage locker, drive around slowly and make slight turns. It should engage. I think mine engages easier when it has warmed up a bit from some driving.
 
mine seems to engage quicker when I am in neutral
 
Sorry, i now see that you have a manual, but, what were you doing driving around on tarmac with your rear locker engaged? I would think that could damage your locker.
 
I would lock the centre diff, get the back end up on jackstands and with the key in the ON position, turn the dial for the rear locker. You should be able to hear the actuator cycle. Once it cycles, spin one of the rear tires and see if the rear will lock.

If it doesn't lock, it should be a problem with the actuator.
If it does lock, it should be a problem with the switch that tells the ECU that the axle is locked (which turns on the dash light)

Start with that, and hopefully someone with more locker knowledge than I will chime in soon! :cheers:
 
Also, the locker actuator will not cycle until the truck is going 8km/h (5MPH) or less. So if you were going faster than that in your figure 8s that could explain why it didn't lock.
 
Is your center diff lock light on? If not then you have a problem with the ball switch that tells the computer to allow engagement of diffs. I would look at Post #6. Can only jack up one side(locker side) if you want(not both), spin tire.
Then again as in post #6, If you feel locker engage, then you will need to check the ball switch to see if it works or needs replaced.
Ball switches will go out from time to time.
 
"what were you doing driving around on tarmac with your rear locker engaged? I would think that could damage your locker."

i was trying to give it a good kick up the back side!

i will jack the back end up tomorrow, just to confirm that it isnt locking really as im sure it isnt.

like i said i can here the actuator cycle. ive never had a problem with the rear before then it just stopped working.

centre diff light comes on and front diff locks no probs.
 
I had trouble with my rear also, I took the ball switch off and cleaned it put it back and it has worked for me ever since. Same switch powderpig is talking about.
 
Mine did exactly what yours is doing. I took the cover off were the worm drive is and manually turned it a few times. That fixed it, lubed it up and went out and ran it for a while in the dirt. Pm me if you have any questions.
 
didnt have time today. had to do a few jobs on the GF's rav4!

what is this ball switch of which you speak? did a quick search and couldnt find anything.

haskins, this sounds promising. you mean take the actuator cover off?
 
what is this ball switch of which you speak? did a quick search and couldnt find anything.

Not sure if they are the same on the rear locker, but on the center lock look at this write-up: Troubleshooting the Toyota FJ80 Land Cruiser Center Diff Lock (CDL) | Pacific Northwest Backroad Adventures

About half way down he describes these switches.

When i was troubleshooting my center lock issue, I remove the 3 and tested them. I just used a open wrench to get out, can't remember the size.. .19mm maybe. Carefully not to get any debris on the ball when putting back in.

hope maybe part of that helps.
 
Chapel Gate what was your resolution did you get it working? My rear just started doing this as well I've read a few threads to get a few ideas to try this weekend.
 
the ball switch is on the locker motor. it just tells if the locker is engaged or not. i had issues also, working the motor didn't help, so i pulled mine apart, cleaned it all up, greased it up and retimed it (someone here posted up the ohm readings to properly time the motor). it's worked great ever since.
 
Back
Top Bottom