Real-time help needed! Stall when applying gas

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 5, 2004
Threads
18
Messages
94
No longer REAL-Time! Stall when applying gas

Sorry to be brief--but need to get back to the family.

Driving down the road ~25 mph, the engine stalls and dies. I coast to a stop, and cut the ignition. I turn the key to start, and engine starts up just fine and idles. Applying the throttle causes the engine to die. I took out the EFI relay for a few minutes and replaced, but no difference.

It is starting and idling fine, but any application of throttle is causing the engine to die.

No CEL, and new O2 sensors within the past 2k miles.

Any ideas?

Thanks!
 
Last edited:
Is your throttle position sensor hooked up? Are you anywhere that you can use a multimeter? Do you have a CEL?
 
So.... if you leave it idling will it? or does it sputter and die? Might be fuel related. Fuel filter? The fuel sock in the tank? or Clogged air filter? Someone chime in please.........
 
See if you pass this inspection... this is the TPS
tps.webp
 
The first thing to check is the air input tube from the air cleaner/MAF to the throttle body. It can develop cracks creating a poor air/fuel mixture. Seal with duck tape if this is the case.

Make sure the battery and cables are in good condition and the fuse links are not twisted, corroded.
...
 
How quickly does it die out when you get on the gas?

Does it get worse as you give it more gas? Can you keep it running and give it a little gas? Is the problem intermittent?
 
Fuses look good, battery connector is good.
It turns over without hesitation, starts up, idles like a champ...it's only when I apply throttle that it dies.


For the diagram above, it states to "apply vacuum"--of course if I open the throttle it will die, and therefore I assume no more vacuum. Can I properly test the circuit with the engine dead and throttle held open?

--oops-just saw the part about using a feeler gauge to get proper throttle position. So how do I apply vacuum?
 
I don't know if applying vacuum is absolutely necessary, but you should see a change in resistance across VTA-E2 when you open and close the throttle plate even with the engine off.
 
Thanks Nator.

I'll be heading back to the vehicle in about 30mins and will do the voltage check.
However, since I've got to get the family out to the airport next morning, I may just have to have it towed to the shop. Unfortunately, time may necessitate spending the $$ for a shop on this one.

Fortunately, the cruiser is only minutes from home and we're not stranded on a highway, like many others in Colorado.
 
new2mud, just to be clear...
You are measuring resistance, not voltage. You need an ohmmeter (multimeter) and you want to check resistance, it will probably be the omega symbol on your meter :D

Good luck... I'm thinking this has to be SFI related, either low fuel pressure or lean A/F ratio...
 
Roger on the ohmmeter.

Since I replaced both O2 sensors with OEM ones recently, and not getting any CEL, this has me baffled.

Will keep you posted.

Thanks to all for the quick replies--I'll check one last time before I head out in about 30 minutes for any last bits of sage advice.
 
Unfortunately due to ridiculous time constraints I was unable to get to the vehicle and check the TPS--had to go ahead and get it towed to the shop.

Will post back with my learnings once proper diagnosis has been made!
 
OK, family is back in town, and had the 80 checked out by our local mechanic while we were gone.

The problem was so simple it's embarrasing, yet I'm grateful it wasn't a major component failure. Get this--somehow a bottle cap had found its way to the intake, so that when vacuum was applied (i.e. open throttle) it would get sucked up against and block the air intake. Simple as that. No TPS sensor failure, no bad ECU. Bottle cap.

Of the three things necessary for ignition, air is the least likely to be missing--but in this case, thankfully, it wasn't the spark or fuel in short supply.

Many thanks again for the responses!
 
Back
Top Bottom