Radio install help.....

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 14, 2004
Threads
232
Messages
3,965
Location
Virginia Beach, VA
So,

I picked up a double din head unit from a 2002 4runner, and can't get the thing to work well. The ID is AD6803

I have the amp that the radio came with originally.

Problems:

With the radio hooked up, I get really poor sound, and it barely gets loud enough to hear.

I plugged the two gray connectors into the amp, and have tried it both with the factory amp plugged in, and with it unplugged.

From searching on here, the only thing I can find that I haven't done is to cut the power antenna wire.....

Would that help?

Any suggestions would be very very welcome.

Thanks,
Dan
 
Dan,

I'm having trouble remembering exactly, but it seems like when I put the Tacoma unit in mine, there was actually more than one possibility for how to connect it to the harness. That is, with my original unit, there was at least one unused harness plug, and (again IIRC) I may have actually used this plug on the newer unit.

I hope this makes at least a little sense.

Curtis
 
When I installed an aftermarket stereo into my ex's 2000 4Runner, I think the 00's are the same generation as the 02's, we could get power to the stereo, power to the antenna, but no sound at all. I asked around and was told if you bypass the factory amp, it will solve all of your problems.


If it's possible to plug the harness into the place where the amp plugs into, try it and see what you get.


But I just ended up cutting the harness off completely and used the wiring diagram from a website, I believe it was the12volt.com, I just used wire nuts to connect each of the wires to the correct ones on the new stereo's wiring harness. It took a long time, but it's what worked.
 
Alrighty,

The connectors from the harness will not plug into the head unit in any way shape or form. The two gray ones will plug into the amp, and the amp plugs into the HU. I get the same result plugging into the harness connectors as I do plugging into the amp connectors.

Curtis, The plug that I used for my old radio doesn't fit anything, so the unused plugs are the ones that fit the amp. Did your radio have the built in amp or the separate amp?

Thanks again!

Dan
 
Koffer,

Does this involve more than just screwing the brackets down to the body? I thought that the ground could be an issue because the HU won't work unless grounded so I screwed the amp down too, but no change.....
 
I think there was a wire
I need to look at my notes (if I can find them ) but Im pretty sure there was a white wire with a black strip on it in the radio to amp harness by the connectors that plug into the stock toyota harness .

if you could take a pic of the harness that came with your radio I may be able to tell you better.
 
Curtis...
...Did your radio have the built in amp or the separate amp?

Dan,

I'm afraid I honestly don't know the answer to that question.

My guess would be no if the exterior amp is supposed to reside behind the dash near the head unit; I didn't notice anything back there.

One (or two?) of the harness connections definitely worked in the newer unit that I installed. It also had other inputs that I plugged nothing into; I guessed that those were meant to be used in other vehicle applications, but really I have no idea.

Sorry if I misled you at all in thinking the 4runner unit would work; did you have to pay much for it? :frown:

Curtis
 
Ok here are the pics

First is the connectors at the amp
(the gray connectors in both pics are identical, and both plug into the new amp)
second is the connectors behind the radio

Third is the back of the new radio
stuff to sell and prichard wheeling 056.webp
stuff to sell and prichard wheeling 057.webp
stuff to sell and prichard wheeling 071.webp
 
Next is a pic of the amp to radio plug

then a pic of the wires going from amp to radio

Then a pic of the amp...

Curtis, no worries at all. This is not the same unit that you ended up with, and I took a chance buying it. It has the green back lighting to match the cruiser, and I payed less than 50 bucks shipped. Worst case scenario, the local boneyard has a couple units that I could trade straight across for. We'll get it figured out one way or another....
stuff to sell and prichard wheeling 061.webp
stuff to sell and prichard wheeling 065.webp
stuff to sell and prichard wheeling 066.webp
 
Mucho different then the JBL amp I had to put in for the Toyota Navi
The only thing I can think of is see if you can find a diagram for the new unit and go from there .
Sorry about not knowing much more . Its now in the area of me needing to get my fingers and mind wrapped around it .

Sorry I wish I could help more
 
Anybody else?

I plan on installing the HU into my t100 this evening to see If I have any better luck. It may be a bad unit despite the seller's guarantee....

I also plugged my old radio back in to make sure I didn't fry anything, and it works just fine....
 
Ok, the radio does the exact same thing in my T100. The T has the two plugs that fit in the amp, and the the resulting sound and fuzz was exactly the same as the 80..

Time to return it I guess....
 
Ok, the radio does the exact same thing in my T100. The T has the two plugs that fit in the amp, and the the resulting sound and fuzz was exactly the same as the 80..Time to return it I guess....

Sometimes you gotta go it alone on these trial and error trips. We were cheering for you. :bounce:

Glad you figured it out. I hate :ban: stereo wiring.
 
I talked to the seller a bit, and had a question: Could this be caused by a bad amp?
 
I talked to the seller a bit, and had a question: Could this be caused by a bad amp?

If you want to try a different amp, I have the amp from a same generation 4Runner, but I cut off the harness.


Because when installing the new player in the 4Runner, I just bypassed the amp because otherwise I couldn't get any sound out of the player. :mad:
 
Back
Top Bottom