R&P setup -- approx cost

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 3, 2008
Threads
39
Messages
148
Location
Logan, UT
I am wondering what I'd need to pay for putting new gears in a '94. I'm in Utah, so any recommendations in the north would be appreciated...

Also, does having factory lockers affect the cost or experience needed in a shop?

Uh, finally, best deals on 4.88s? Anyone have a set to sell off? :D
 
If you pull the third members and take them to a shop, I would expect to pay around $50-$65 + parts for each set to be installed. If you drop off the vehicle, you're probablly looking at book time + parts.
 
Last edited:
I heard Big O tires of South Ogden does a sweet job-----NOT they suck major cahones! Never go there, they will jack your rig up.

I would check out Cruiser Outfitters in SLC. I hear they do a great job. Kurt (the owner) is a mud member too.
 
If you pull the third members and take them to a shop, I would expect to pay around $50-$65 for each set to be installed.

The "good guy" price in Albuquerque is significantly higher than this. IIRC, mine were $500 for the pair. I think he quoted $300 for the rear and $250 for the front if done individually. This was with me pulling the 3rds and dropping off at their shop and allowing them a loooooong time to work in time to do the set-up around their other projects.

The e-locker rear requires some special Toyota-Only shims or a creative installer. It is a lot of work and $500 was a very fair price.

Look at about $500 for the gears and install kits plus another $200 for front axle service parts. It is a good idea to do the front axle service at the time you do the regearing. Figure $1,200 minimum for the regearing job with you doing most of the labor.

-B-
 
The OP was asking labor to set up gears. If guys can get 250-300 to set up a R&P they are making some GOOD money. I'll admit the rear elockered 3rd's aren't a walk in the park, but I couldn't look someone in the eye and tell them they are getting $300 of labor out of me.
 
I am wondering what I'd need to pay for putting new gears in a '94. I'm in Utah, so any recommendations in the north would be appreciated...

Also, does having factory lockers affect the cost or experience needed in a shop?

Uh, finally, best deals on 4.88s? Anyone have a set to sell off? :D

Call Kurt at CruiserOutfitters for the parts, he is down in SLC. If you pulled the diffs I would expect to pay 175-200 each for the labor to install the gears. Kurt should be able to arrange the installation or at least recommend where to have it done.
 
x3 on those labor rates, around my area, your looking to pay $200-300 each third member just to have gears set up, and that's bringing them the third members by themselves!!
 
Perhaps I'm not charging enough then! Setting up a 3rd member right isn't exactly rocket science or that labor intensive. I did edit my op to include "+ parts".

Let me be sure that I understand.

You do gear setups and charge customers for the labor, correct?
You will do a front 80-Series gear setup for ~$50 if we supply the parts & shipping?
You will do a rear 80-Series gear setup for ~$65 if we supply the parts & shipping?
Are you familiar with Zuk and have you reviewed his gear setup process? Do you use a comparable process?
Approximately how many 80-Series gear setups have you done?
What is your contact information so members can contact you?

-B-
 
Just to let you guys know we sell the complete kit shipped for 699.95.

2 rebuild kits
2 sets of gears
shipping included.

Thanks Cam
GM IPOR

PS. We charge 4 hours per diff to setup a third member.
 
A good source - Optional

Not to offset the recommendations of the other members, I do know of someone you might also consider speaking to. His name is ZUK, and he has a website Toyota Gear Installs - I have spoken to him personally and all he specializes in is Toyota 8" & 9.5" R&P's. He can give you info on gear sets, install costs and has a reputation known all over yotatech.com, 4x4wire.com and so on. Many people use him and you can see his work at his website. I suggest it at least as a second opinion.

Here is just one of many 1997 FJZ80 he's done - pm me if you like his # : http://www.gearinstalls.com/97fzj80rear.htm


John
 
Back
Top Bottom