Question and intro in one post

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 19, 2007
Threads
5
Messages
20
Hi,
We, it's actually my brothers, have a 95 FJ80 with factory lockers front and rear. It's a solid vehicle with 160K. It's been in the family since it was new. Anyway I am the car guy in the family so I finally got the time to replace the front knuckle bearings since the shop told my brother they were bad a few months ago. I am used to American 4x4's so this Toy thing is new to me. I did search for this stuff and really didn't find the answers I am looking for. I pretty sure I know exactly whats going on but I want to be sure. We took it apart and found an unbelievable amount of sludge. I've done hundreds of diff services so I know what I'm doing and what should be in there. Obviously it had been neglected. There was sludge/oil in the knuckle with the CV joints on both sides. So first question, that is suposed to be full of grease only and not oil right? I read yesterday that the CV is lubbed by the gear oil which I am 99% sure is wrong. Anyway we got all new seals, gaskets and bearings and did our best to clean out the axle housing. We have just about got everything back together. We cleaned/powerwashed everything real good including the CV joints. Now I want to be sure of three things since I am always working on U-joints and not CV's. One. With the CV joints completly clean is it normal for there to be some slop in the balls/joint? Second. We packed the CV's real good with grease. But should we completly fill the knuckle with grease as well? Or just add a good handful in there and call it good. Third. It seems weird to me that the stub shaft does not ride in some sort of spindle bearing inside the spindle. All other American axles I have worked on have a bearing inside the spindle for the axle to ride in. Seems without one it can be sloppy. I assume it's fine since there was not one in there. Looks like there is just a bushing of sorts with grooves in it. Thanks yall for the info and sorry for the long post.
 
First things first, Welcome to Mud! :flipoff2:(official welcome). We need pics!

Congrats on the axle rebuild. Did mine just a couple of months ago. Check this thread regarding a rebuild https://forum.ih8mud.com/showthread.php?t=78276
It is an excellent write-up and most folks refer to it for their first one or two rebuilds. Post #1 in the thread is a cut away of the spindle/Birfield and should explain how the spindle rides in relation to the Trunion bearings (you replaced these?). Post #19 in the thread shows how full you want the knuckle. You mention seals in your post, so if you replaced the inner axle seal you should no longer get the sludge that results from diff oil getting past the seal and mixing with the grease in the knuckle.

There is a wealth of information in the FAQ of the 80s section on all kinds of repairs/upgrades/troubleshooting.

And it bears repeating...post some pics!
 
On the last one I did (Wife's), I used 80/90 gear oil in the differential and synthetic molly grease in the birfield, knuckle and bearings. The knuckle should be about 3/4 full. Not completely full, but most of the way there. It takes a -lot- of grease. Doing it with synthetics is very expensive and I wouldn't do it to a vehicle that I thought I would be back in there in the next 4 years on. My build truck has dino greases.

The grease in the bearings and the gear oil in the diff are held apart by that little rubber inner axle seal. When it goes bad (not if, but when), they co-mingle and give the birf soup that you saw on teardown.

Be sure to inspect the bearings well. If you replace a bearing, replace the race. Normal stuff.

Welcome! :flipoff2:
 
Third. It seems weird to me that the stub shaft does not ride in some sort of spindle bearing inside the spindle.

Most of your questions were answered correctly above. During the production run, Toyota used a brass spindle bushing. Replacement bushings are available if there is too much wear. Post-production (actually with the 105 models we didn't get in the US), Toyota superseded the spindle with one that has needle bearings. These new style spindles are available from Cruiserdan and they are a work of art. (Not too spendy either.)

The other question you asked that wasn't addressed was the "play" in the CV joint (aka Birfield.) These are durable components but, if neglected, they will develop deep grooves where the balls wear into the tulip. The typical indication of excessive wear is clicking from the CV during slow-speed turns. It has been reported by some that swapping sides will change the wear pattern and reduce the clicking, though a worn-out part is a worn-out part and should be replaced when possible. The Birfield is not serviceable through Toyota. After-market versions (both DD and off-road) are available.

-B-
 
Last edited:
Welcome. I got nuthin' else, these guys know what they are talking about.

Good luck!
 
Thanks for replying to a newb. I know how these things can get asked a million times. Cubiclecaptive, I did read that post when I did the searching and it gave some good info. Just not quite the exact answers I was looking for. We are just about all set except for one little question. On the FJ80 we are working on it has dust shields. So I am thinking that there should be two seals at that point. One on each side of the shield. Currently we have it as follow: From the face of the knuckle we have the very thin hexagon like seal, then the spindle, then a circular seal then the dust shield then the bigger metal flanged seal, then the rotor. Now if there was no dust shield there would be a seal between each metal surface. But being that we have a dust shield there is metal to metal ( the dust shield and then the metal flanged seal.) Seems to me there should be another seal between the dust shield and the metal flanged seal. Anyone know about that?
Thanks again for the info.
Chris
 
There are 2 diagrams showing all parts, including all gaskets, in the link given to you in post #2.

attachment.php


attachment.php


This wasn't your question but note that the above diagram shows multiple shims for illustration #43233. They come in different thicknesses. I am not aware that anyone has had to re-shim the knuckle so this topic gets little discussion.
-B-
 
Last edited:
I have seen all the diagrams but as I said they don't show a dust shield. The shimming of the knuckle bearings is not an issue. The bearings didn't require any shimming. I am wondering about 43436. Seems to me I should use two of them. One on each side of the dust shield (not shown in the diagrams.)
 
I have seen all the diagrams but as I said they don't show a dust shield. I am wondering about 43436. Seems to me I should use two of them. One on each side of the dust shield (not shown in the diagrams.)
The above diagram is correct.

If you have a part that is not shown in the above diagram then you have the wrong part or something in the wrong place. Where did you get the knuckle kit? Post a pic of this "not shown in the diagram" dust shield and maybe we can help you figure out the problem.

-B-
 
Are you asking if there is a gasket between 43511A and the brake shield?

attachment.php


There is not a gasket between those 2.

-B-
 
Back
Top Bottom