Problems w/ 65 FJ40

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 25, 2006
Threads
5
Messages
21
Location
Florida
I am have recently been turned from a Jeep owner/lover to a Cruiser owner/wanna-be and don't deserve it yet lover. I just bought a '65 cruiser from a guy out of AZ. My new FJ40
It just arrived today and as you would know I was very excited to take it for a drive. The shipping had me meet them just of the Interstate so they didn't have to drive through the city which is fine. When I picked it up there were a few problems and things that are weird. Number 1: about 5 psi per tire and no gas which is the fault of the buyer no big deal. I started to drive it and got it to the gas station and realized very quickly that I will be installing power steering. The next problem happened right after filling up with gas. I was driving and sparks started shooting out from behind the gauges that are above the heater in the middle. All of a sudden the amp gauge caught on fire and the whole cruiser shut down. I don't know exactly what happened and don't know where to start. Done a lot of jeep work but never electrical and haven't even found '65 FJ40 repair guides. Any help would be greatly appreciated. Thank You
 
Welcome to CruiserHood!!!! You'll never go Back Fo Sho. Sounds like you had a major melt down. No big deal though, the cause should be very easy to find considering the fire. I'm thinking a hot short for sure, somewhere behind the dash. Spend an afternoon cleaning up the old wiring, and you'll be back in the drivers seat.
Good luck.............
Greg

The tech manual I have only goes back to 1968, but if you want me to scan an electrical diagram let me know.
 
So pretty much just go through and replace all the wiring? That should be easy. I have found 68 diagrams myself. It shouldn't be that different hopefully. Should I Install some fuses?
 
Installing some fuses couldn't hurt in the least. Check with Summit or your local speed/4x4 shop for a fusable wiring kit. I wouldn't think all of your wiring needs to be replaced, but the critical systems, i.e. battery, alt, starter etc, should recieve a thourough once over. The rig is new to you, so an in depth, all around inspection will give you a list of items needing attention first. Safety first Bro.
 
Cards4Life said:
I was driving and sparks started shooting out from behind the gauges that are above the heater in the middle. All of a sudden the amp gauge caught on fire and the whole cruiser shut down.
Sounds like you might've nailed it right there. I'm guessing something came in contact with the exposed terminals on the back of the amp gauge. (Been there, done that. :o ) Hopefully the damage didn't go much further than the wiring in that area. But, I would check the entire electrical system following an incident like that.

And, make sure you disconnect the battery when you pull / re-install the instrument cluster or working around behind the dash.


By the way, Welcome!!!
 
I had something similar happen on my 67, the location of the sparks makes me think that something came in contact with the fuse block. The factory block had a cover on it (you can still get them new at the dealer- the whole fuse block with cover). The covers fall off, leaving all of the terminals on the fuse block exposed (right on the firewall, next to the heater-)

I am guessing the gauges are aftermarket ones- not the factory ones on the dash?

I had replaced the defrost duct with one of the metal flexible universal ones. Bad idea- ZAp...new fuse block. All of my wiring was fine, I just needed to replace the block- I think it was around $35 from toyota. I would start therebefore a rewire.

Hope it helps.
 
I'm guess the gauges your referring to have to be aftermarket because otherwise they are already fused in the fuse block. As for a diagram I don't think you'll find one for pre 68, same as you can't find a lot of info on the early f which is the engine I have. But 68 should be really close if not the same.
 
So I found the wire that was screwed. It was connected to the Ammeter which is the one that caught on fire. I followed the wire and it was connected to the starter motor. So what I did is clipped the wire. I tried to jump it and I got a ticking sound coming from the starter motor. Need some help. So I know that the positive for the ammeter comes from the starter (the one I cut) and the negative goes to the alternator. Does this circuit have to be completed in order for the cruiser to run? I am just trying to figure out if the problem is beyone that 'cause it won't start since I snipped it. So it is telling me that I either have to complete the circuit, it is a bigger problem, or both. If anyone knows it would be greatly appreciated...
 
Last edited:
Cards4Life said:
I found an ammeter is part of a circuit so I will need to replace it to complete the circuit.
Correct the amp meter has to be wired for it to start. Is tha gauge fried or just the wiring to the gauge? Good luck and welcome to Mud and Cruiser-dom :)
 
The gauge and wiring are fried so I was going to go get new wiring and a new gauge. I don't know what gauge wire to get though....I don't want it to happen again you know..... Thinking about putting in a fusable link while I am playing in that area too.
 
Considering that the engine is changed from original it's likely that little of the original wiring exists, so a diagram might not help much.

The previous owner is a member of this forum, though, so he might volunteer some help.

I'd consider myself on my own with it and probably look into one of the aftermarket harnesses to get the wiring redone from the ground up. It'll be better in the long run to do that and save the possibly endless glitches that old and redone as needed wiring can bring.
 
Welcome, I have yet to see a wiring diagram for my 65 and I have been looking for something for a while. I have looked at two options with regards to the wiring on mine. Rewire everything that is not working, lots of cutting and splicing. Or buy a painless wire kit and completely go through everything and make everything look new. I am personally going to go with the latter, I have had many freak fires like that and spent too much on fire extinguishers. Good luck!
 
There is a less expensive option that people have said works as well as a Painless harness. About half the price and I don't remember the name but someone will come out with it soon.
 
alright.....need some help....I replaced the triple gauge (ammeter, water temp, and oil pressure) and the burnt wire connecting it to the starter motor. I also put a fusable link in the middle of that connection. The fuse is a 40. Is that to strong? Here is why I ask. I went to drive it and something started to smoke behind that gauge again. Could it be the voltage regulator? Thanks for the help!
 
The amp meter carries the full amperage capacity of the battery into the cab and has exposed ends where it bolts to the ammeter, It is also the main feed for the electrical system before fused power. Both these situations were something I was not comfortable with. I bypassed the ammeter completely by un screwing it from the back of the meter and connecting the two wires together then thoruoghly insulated it with shrinktube and tape. To monitor the charging system I use a volt meter which you can attach to a fused 12 volt source, much safer IMHO.

Just as a side note you bought that crusier from a member of mud that goes by the name SONORANFUN. Many members here have posted and stated very unsatisfactory transactions with this person. Do a search and read some of the posts involving him and decide for yourself. Granted it is a little too late in this case but it may help for the fututre and most of the posts are entertaining to say the least. Good luck!
 
tfdcruiser said:
The amp meter carries the full amperage capacity of the battery into the cab and has exposed ends where it bolts to the ammeter, It is also the main feed for the electrical system before fused power. Both these situations were something I was not comfortable with. I bypassed the ammeter completely by un screwing it from the back of the meter and connecting the two wires together then thoruoghly insulated it with shrinktube and tape. To monitor the charging system I use a volt meter which you can attach to a fused 12 volt source, much safer IMHO.

Just as a side note you bought that crusier from a member of mud that goes by the name SONORANFUN. Many members here have posted and stated very unsatisfactory transactions with this person. Do a search and read some of the posts involving him and decide for yourself. Granted it is a little too late in this case but it may help for the fututre and most of the posts are entertaining to say the least. Good luck!
Yea I was not too happy with his expanation of the vehicle compared to what I received but at the same time it is totally rust free which is huge for me considering my last cj didn't even have floorboards.
 
Back
Top Bottom