Prep for Maiden voyage

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

My god that is a lot of stuff for a 900 family weekend trip. :)

But at least you will be hauling in style knowing you got pretty much everything covered.

Nice truck.
 
Thanks much, all. Just got home. To address some of the comments.

Most of the loaded gear was to see how the truck can handle the weight on a longish trip, not that we needed half that stuff. And handle it, it did, just great. I worried that performance would be seriously lacking with 285s and a lot of weight and while it's no hot rod, it's plenty fine for me. Of course, I'm coming from a 5300lb Toyota 4x4 truck with 100 h.p. engine and 35s, so I'm easily impressed with anything that has even marginal passing power.

Regarding the hi-lift, I used Slee's off road light tabs and bolted a bracket that allowed me to bolt on the hi-lift and a set of lights. I personally think the light tabs are plenty strong, but obviously, that's not what they were designed for. The only problem is that the hi-light can block the very bottom part of the headlights and the radiator. So far, I haven't noticed any issues.

We'll have to see if the radiator get's enough flow in the desert summer, with the lights, high-lift and winch solenoid in the way.

Regarding the Ham radios... friend of mine and I got licensed a few years ago so we could communicate with each other, but I never got into it like some folks and rarely use them these days. However, I do feel a lot better having 50 watts of 2 meter power out in the middle of no where well out of cell range.

The trip went very well, and the wife got lots of seat time. The fact that she felt comfortable driving it, speaks volumes about how well designed these rigs are even when modified. I didn't get any real off roading in, but I did take it up some seriously windy and steep logging roads and it really struck me how much low end torqe the motor has. I had a carload of people, and gear and still never needed low range. I did keep it in 1st gear a few times and it just crawled up the hill like it wasn't even there. I barely used any power, to keep things nice for the passengers, but I have no doubt it would have climbed that hill like a banshee had I hammered it down. Very impressive.

My truck would have required 4 wheel low, and the foot to the floor with the motor revving to climb that same hill, even with 5.29s. My truck has served me extremely well, but I won't be missing it much after driving this thing.

Did a lot of high speed driving on some seriously windy back 2 lane country roads and all I can say is, if you haven't...DO THE CASTOR CORRECTION. This thing handles and drives like an absolute dream with the castor correction. And I never thought a lift could handle this well. I'm very glad I did the 2.5" lift, instead of the OME low lift that I was contemplating.

My only complaint, which I am apparently not alone...is that the brakes truly suck, even though mine have almost all new parts from the prior owner. If there's some majic brake pill, I'd sure love to know about it. But otherwise, I couldn't be happier with this rig and look forward to many years of travels and modifications.

Of course, there's gas mileage, but we all knew that going into it. I did get about a little less than 14 mpg average on the trip, doing mostly 70 on the highway. From what I hear, that's not bad considering how my rig is outfitted, but I wonder how a tune up would make it perform. I'm still running the original plugs, cap and wires that the factory workers slapped on back in Japan.

Special thanks to this board. The amount of information that I've learned in the last 6 months is off the chart. I couldn't have done it without the information contained here.
 
Last edited:
Brian, I love the truck and all the goodies...
Glad your trip went off without any glitches sounds like you are very pleased and should be with a rig like that:cheers:

I hope to do many of the same or similar mods in the near future:)

I like to hear how you say it still rides great on the rode even with the lift and extra weight added:D

Congrats on a excellent build! Jason
 
Brian,
Awesome rig!!! definitely hope you consider ROTW b/c I for one could learn a few things! couple of things...were in OR did you go 900 miles would have put you near the southeast corner...is that were you went?

also the 2.5 lift was that a heavy front and rear or something else? thanks for the write up...and if I get a chance when i am in portland one of these times i would love to catch up!

barrypt5
 
yup, I think that one should be able to come back from a day or 2 of asphalt driving in that great rig...! :)

and now for the dirt trips!
 
Brian,
Awesome rig!!! definitely hope you consider ROTW b/c I for one could learn a few things! couple of things...were in OR did you go 900 miles would have put you near the southeast corner...is that were you went?

also the 2.5 lift was that a heavy front and rear or something else? thanks for the write up...and if I get a chance when i am in portland one of these times i would love to catch up!

barrypt5

I would be honored to be ROTW sometime, but I still have a lot more work to do and would like to a get a good long trip in first. I will be detailing some of the mods on this section of my website as soon as I get a chance:

http://www.brian894x4.com/ExpeditionLandCruiserFZJ80.html

The lift is heavy front and medium rear, no trim packers or anything else.

If you have any questions, feel free to ask here or PM or email anytime. Oh...and your right, it was about 600 miles round trip, not quite the 900 I thought. We did a loop from Portland to Southwestern Oregon and back.
 
I'd highly suggest looking into solidrock offroad's sliders, They are what I have, and super nice.

But, if you want to save on shipping Metal tech is in beaverton or Aloha, and their are super nice as well.
 
Back
Top Bottom