PHH Brotherhood

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 12, 2007
Threads
15
Messages
138
Location
SoCal
I just want to say that replacing the PHH was the most aggravating experience I've ever had working on a vehicle.:mad: I just wanted to say cudoes to all those that have changed it. I feel as though I'm a member of a special brotherhood. This may sound a little mellow dramatic, but man, could it be any more difficult. I could go into details about my trials, but I won't burden you all with it. I'll just say, 10 fricken hours later and a lot of :crybaby:, it was done. I know it shouldn't take that long and if I had to do it again, I could probably do it in 2. Fortunately, it's something I'll never have to worry about again.:D Anyway, I just wanted to say that I have a new found respect for those that have taken on this challenge. Knowing I wasn't alone on this endeavor kept me going and prevented me from throwing in the towel. So THANK YOU ALL!!!! :beer::beer::beer::beer::beer::beer::beer::cheers:
 
Congrats! It sucks! But you're done! :beer:
 
What caused you the most problem?
(1) I pulled the starter (I was rebuilding it at the same time) and the transmission dipstick tube.
(2) Used a dremel and cut the OEM clamps off.
(3) Disconnected the top heater hose from the metal tube and reached from under the vehicle and just broke the middle bolt on the metal tube loose (never, never remove it).
(4) Twisted the metal tube until I had a straight shot at the block nipple and used Astroglide for lubricant.
(5) Once the new silicone hose was on the nipple, twisted the metal tube until it popped on the silicone hose.
(6) Reconnected the top hose to the tube and reached up and tightened the middle bolt (that moved the tube back into place).
(7)Tightened the clamps and took a picture (attached below).

Maybe I was lucky, but it really was not that bad. I spent more time changing the other coolant hoses (I used the wrong tools to get the spring style OEM clamps off and on).

Anyway, :cheers: to you for getting it done!

Riley
DSC00476.webp
 
Driley you were truly blessed by your PHH for it to not be a PITA!

Our PHH was my hardest, simple repair. It looks so innocent until I got in there and started to get things done! Took about 5 hrs!

Anyway, glad to see that you made it thru the ordeal - and you don't have to do it again!

Here's to ya - :beer::beer::beer:
 
The day after I did this there was no swearing or bad language in the universe because I had used it all the day before. I thought that job sucked. Good work.
 
Congrats!!:beer:

I guess I lucked out it took me about 2 hours. Removing the DS wheel and using the Dremel tool are key.
 
What caused you the most problem?
(1) I pulled the starter (I was rebuilding it at the same time) and the transmission dipstick tube.
(2) Used a dremel and cut the OEM clamps off.
(3) Disconnected the top heater hose from the metal tube and reached from under the vehicle and just broke the middle bolt on the metal tube loose (never, never remove it).
(4) Twisted the metal tube until I had a straight shot at the block nipple and used Astroglide for lubricant.
(5) Once the new silicone hose was on the nipple, twisted the metal tube until it popped on the silicone hose.
(6) Reconnected the top hose to the tube and reached up and tightened the middle bolt (that moved the tube back into place).
(7)Tightened the clamps and took a picture (attached below).

Maybe I was lucky, but it really was not that bad. I spent more time changing the other coolant hoses (I used the wrong tools to get the spring style OEM clamps off and on).

Anyway, :cheers: to you for getting it done!

Riley

For me:

(1) Pulled out starter. Had to replace because of intermittent starting issue. Wanted to replace the Bosch with OEM starter.

(2) Kept poking the hose with blade to cut it up and pushed clamp with screwdriver until it got lose. (Sounds simple but did this for an hour)

(3) For the next hour used blade and fingers to remove the rest of the hose.

(4) Exhausted, fell asleep under the truck until my wife called me and woke me up.

(5) Placed hose on block tube and used Chamis Butter to lube. Tried soap but kept drying up.

(6) Couldn't get metal tube to align. Spent about 2 hours trying to figure it out. Then went to Sears to look for something that might help. No idea what I was looking for, but thought if I saw it, I'd know. Got a crowbar. Worked great. Fixed all my problems.

How the heck did you did you reach the second bolt for the metal tube? You must've not done a lot of bad things in your life. Now you are rewarded with an easy PHH replacement. I on the other hand did many bad things.:grinpimp:
 
How the heck did you did you reach the second bolt for the metal tube?

I read on here that a swivel head, gear drive box wrench was required. Went to Harbor Freight and spent the $30.00 on the set of metrics. Laying under the LC, reached up and started feeling around until I found it. I only loosened it about 1/2 turn, but it was enough to allow the pipe to twist back and forth. It took reattaching the top hose to get the pipe back into position.

As mentioned before, the dremel with a small cutting wheel was really a time saver. I attempted to pry the clamps off after cutting the old PHH in half, but realized it would take quite a bit longer than just cutting (carefully!!!) through the OEM clamps.

As far as falling asleep under the LC or exhausting the world profanity supply, both were experienced when I replaced the (2) larger coolant hoses (connect the bottom of the radiator to the thermostat housing). I really needed a large enough set of straight jaw pliers (not channel locks) or the cool tool cdan recommended.

Again, :cheers: to all that got this done.

Riley
 
Back
Top Bottom