Painless is painfull

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 28, 2002
Threads
558
Messages
8,124
Location
Kamloops, BC Canada
Website
www.shopraddcruisers.ca
Been a few days and have to say its not all that user friendly.

I would work on restoring a old harness the next time compared to installing this generic POC.

Come to think of it after pulling the 1965 wiring harness, it easily could of been repaired, most of the problems were PO doing some wiring themeselves.

It was said in one thread by fellow cruiser head mechanic that he would easily repair a cruiser harness than throw one of these units in(David Dearborn).
 
they are all painful. I didnt use a painless harness, I used a EZ wire one because it was half the price and just as good. BUT that said- they are all the same in terms of installation. Its just a fuse block with a bunch of wires. And you have to figure out where they go... You just have to follow the diagrams and double check your work. If all youre looking for is to clean up a few bad wires, probably fixing the stock one is best. But if you want new connectors, heavier gauge wire, new fuse panel, and more circuits- then a new harness is the way to go. Plus the wires are labeled all the way down the line. A great thing when youre in the back of the cruiser trying to figure out which green and black striped wire does what. Dont give up. It'll be worth it when your headlights shine brighter than a lighter.

cheers-
Dustin
 
Ya I hear ya, in fact the painless is writting down the wire that makes it quite easy.

Truth be told I hired someone to install as I was to busy(or lazy), well I payed the guy 200 bucks to leave and spent 6 hours pulling the harness and fixing all his mistakes.

If he had read the directions it was pretty strait forward, I am knee deep into someone elses job.


Would of been easier if I had done it myself, doing it twice is no fun and twice the work.
 
I agree with the more ciruits and heavier wiring, but how did you deal with the windshield wipers as the wipers require five wires and there is only one hot wire to switch and the rest you have to build?

Would not adding a second fuse panel which is ignited by the key also be a good option for accesories, I have installed such a circuit with good success.

What is the weak link in the old fues and wiring on the older cruisers?

Just curious.

Rob

dustin said:
they are all painful. I didnt use a painless harness, I used a EZ wire one because it was half the price and just as good. BUT that said- they are all the same in terms of installation. Its just a fuse block with a bunch of wires. And you have to figure out where they go... You just have to follow the diagrams and double check your work. If all youre looking for is to clean up a few bad wires, probably fixing the stock one is best. But if you want new connectors, heavier gauge wire, new fuse panel, and more circuits- then a new harness is the way to go. Plus the wires are labeled all the way down the line. A great thing when youre in the back of the cruiser trying to figure out which green and black striped wire does what. Dont give up. It'll be worth it when your headlights shine brighter than a lighter.

cheers-
Dustin
 
all the fuse panel and the wires do is provide hot current to your switches. So in the case of the wipers, your wiper circuit goes to the switch. Then you either reuse the rest of the old wipers harness, or build a new one. I chose to reuse the old wiper harness on mine since it was easiest, unmolested, and didnt have probs. You just splice into it where the old hot wire was. Same for gauges. Your lights and turn signals do have all the "plumbing"- meaning you have the hot current to the switches, and then it provides wires from the switches to the respective lights. The lights are the most difficult to figure out with the turnsignals/ hazards/ brakes. But draw it out and it'll make sense. Let me know if you need help weeding through them.

in my opininion, the old fuse blocks suck. Mine was all rusted, and causing more resistance than power output. This heated the wires up and you would burn your hand on the fuse block. I was always dealing with bad wiring issues... But, yours may be in better shape and certainly adding a second fuse block wouldnt hurt.

-Dustin
 
The Painless kit is bit of a pain if you are not familiar with their product and even then it can prove to be a test of patience.I ran their kit on my project along with all of the factory Toyota switches and the only area that was an issue was the turnsignal/hazard circuits.The Painless kit said Landcruiser/Scout on the package but there is absolutely no reference to Toyota in the manual.I tried to contact the Painless tech. department on several occasions but they declined to get back to be?! I managed to figure it out on my own with a bit of cursing along the way but after all was said and done it works flawlessly.Luckily I have used their products in the past on race cars and muscle car restorations so I have had some Painful experiences to draw from.
 
I went with the Ron Francis harness on my 70 model and it came out great. The can customize the kit to your needs, its very clean and every wire is labled to what part it goes too. It was a breeze to put it in. Mounted it in the tool box under the seat and ran all the wires through a wire loom in the frame. I added a battery shut off switch in the box as well. I will go with the same harness on my 67 when its time.

http://ronfrancis.com/showpage.php?page=detail.htm&partid=120
 
Volunteer said:
I went with the Ron Francis harness on my 70 model and it came out great. The can customize the kit to your needs, its very clean and every wire is labled to what part it goes too. It was a breeze to put it in. Mounted it in the tool box under the seat and ran all the wires through a wire loom in the frame. I added a battery shut off switch in the box as well. I will go with the same harness on my 67 when its time.

http://ronfrancis.com/showpage.php?page=detail.htm&partid=120

Ooooh I like that kit.

Pretty much done, guess its one of those things, next one will get done in a third the time.

Thanks
 
Radd Cruisers said:
Ooooh I like that kit.

Pretty much done, guess its one of those things, next one will get done in a third the time.

Thanks

A friend of mine restores hot rods and he turned me on to them a few years back. After seeing the quality I decided to try them myself and it came out great. Their prices have come down a bit the last couple years, I paid $600 dollars for mine. It came with all billet aluminum switches, I only used the headlight and ignition switches though.
 
Just a heads up about one aftermarket wiring company.

If you are looking for good tech support i have had really good luck with EZ wiring.

The Ron Francis kit does look good though.
 
alumacruiser said:
I tried to contact the Painless tech. department on several occasions but they declined to get back to be?/QUOTE]

Before I even make my point, let me be clear in stating that it's possible for one person to have a good experience and another a bad one. I am not disputing that they did not call you back.

When I put a painless kit in my FJ40, I called their tech support and was told that they would call back. The did call back, I called Friday AM and they called back the following Monday afternoon. Not super quick but weekends are not office hours for them I guess. Point is, I called because I could not figure out the turn signal schematic and why it was not working. I gave up and build a small harness to run side by side with the painless for just the turn signals.

When they finally called back, I told them nevermind, I wanted to get it done so I came up with a work around over the weekend.

They called back a few hours later and said that my harness was defective and that they had mailed me a new one at no charge. I left the defective one in and used the 2nd free Harness in another truck. I was happy.

Painless is not painless, but if your familiar with them, they are not too bad to install. It's one of many tasks that is fairly easy to get done but hard to do a really tight, clean install. Keep that in mind when someone tells you it can be done in an afternoon. Everyone has their own idea of what a good job is...I called it "levels of afflictedness" some people love their afflicted piles of crap and could not be happier. Those are the ones you have to watch out for when they doll out free advice!

Sounds to me like your biggest problem is finishing someone else's work!
 
Last edited:
I am in the market for harnesses too. The EZ harness is nice and cheap and looks pretty good though their site is AWEFUL.. I found this link with all the companies. I have some remnants from a Centech harness, and those parts all look pretty damn badass.. I am interested in quality of the fuse panel as well, FWIW..
http://woogeroo.home.mindspring.com/autolinks/wiring.html
 
Painless has a new waterproof version out, cool but would be hard to repair as it's all sealed up - meaning you could not just pull a terminal off and scratch it up to fix a bad connection.

Summit and Jegs now have their own versions for much cheaper if your a cheapskate like myself.



Openads
 
Last edited:
Painful it is

The painless kit is painful as is all wiring. I did a Holly fuel injection with a Crane distributor and Crane Hi Fire 6 ignition. All I can say is stick with one brand on the ignition components, because it is easier to get tech support on one brand. Put some thought into the placement of the fuse panel like int the glove box and leave it outside as you run all the wires. You will find that you will always need extra lines running to the rear or to the engine components. I did a 12 circuit in the glove box with an external 7 circuit on the firewall. I later ripped out the painless 7 circuit and placed in a bus bar out of a 95 GM S-10.(New and around $12.00 from GM). I then used individual fuses for any external devices running from the bus bar. I also placed a 50 amp bridge (I think that is what it is called) on the bus bar; the bus bar will triger as soon as I turn the key on.
All in all a wiring job is a big ordeal but can be done with patience. Make a list of what needs to be hooked up and leave yourself an extra wire or 2 capped off in the loom. Also buy a toner from Home Depot to track down some hidding wires in the loom and a "Power Probe" from Snap on comes in handy to test for ground, and generate 12V on a wire when hooking up various components.
Have FUN!
 
i have bought summit brand components like distributors, caps, etc and i have not had good luck with their house-brand electrics and engine components. The distributor came defective, and their cap was cheaply made and the points were misalligned. Personally, i would think twice about summit house brand electrics from past experiences. I would not want to pull the wiring out again if it came out defective. a distributor you just pull out.
 
btw we did the painless swap on the 40, and we also ran into the issue with the turn signals in the rear, i think its intended for the newer than 73 rear brake/turn signals where they are separate, rather than the brake/signal using one. To fix it we found some small round brake light and put them on the rear bumper, which work as the signals now. looks stock too.
 
rsrai said:
btw we did the painless swap on the 40, and we also ran into the issue with the turn signals in the rear, i think its intended for the newer than 73 rear brake/turn signals where they are separate, rather than the brake/signal using one. To fix it we found some small round brake light and put them on the rear bumper, which work as the signals now. looks stock too.

Thanks for the heads up about the other stuff they sell, by the looks of the harness they have, it looks like a re-branded painless but that's just a guess. The stuff your talking about is all made in Taiwan like the dist, etc. Junk. I agree. Better to buy reman than cheap ROC parts.

As far as the problem with the harness, that's not the same issue I had. My problem was that wires into the block and they did not come back out!!! Was a manufacturing error. That's why I got a free one.

I was using a generic painless harness (not the Land Cruiser one) and I was using LED 18 wheeler style lights with a 18 wheeler style Signal Stat turn signal/emergency flasher switch.
 
Last edited:
the wire harness that painless and ezwire sell will work in any rig. I have used both. Its all about how you wire it through the hazzard and turn signals. These kits only provide power to and from your switches. The only extra wire harness I have had to make was going to the wipers.

-Dustin
 
Back
Top Bottom