For Sale [PA] 1PZ Parts/Project Engine and Other PZ/HZ Parts

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

deadhead7

deadhead7

Joined
Apr 18, 2018
Threads
13
Messages
101
Location
Beaver, PA
Location
United States
This 1PZ was removed from my 1992 PZJ75 at ~400,000 km to be rebuilt. To make a long story short, right after the rebuild it cracked a head, then the machine shop I used to machine a replacement head (different shop than the one that did the original machining) made an error on machining the replacement head and none of the valves are sealing so the engine won't get compression and therefore is not running. After all that, I decided to abandon that project and instead do a 1HZ conversion of my truck.

The result is that I have this freshly rebuilt 1PZ full of OEM parts but with a junk head on it. Just trying to recoup a fraction of my investment as I don't have the time or patience to get it running again, but this would be a great option for someone who wants to swap a new head onto this engine or use it to cannibalize all the OEM parts for a 1HZ/1HDT rebuild.

In total I have over $4K in parts + ~$3K in labor (machining, injection pump rebuild, injectors rebuild) into this engine rebuild. I'll provide a full list of the parts that went into the rebuild lower in this post.

1PZ Engine - $3,000 $2,500 OBO (+shipping or local pickup near Pittsburgh, PA)
Note that 24V electrical components (e.g alternator, starter) have been removed from the engine as I swapped them over to the 1HZ I installed. Engine comes as-is.

IMG_1517.webp

IMG_1513.webp

IMG_1520.webp

IMG_1530.webp

IMG_1533.webp
 
Last edited:
Picture of the block, crank, and head when finished at the machine shop. The block was bored out to the oversize piston diameter and all new pistons and rings installed.
IMG_6001.webp


Here is the list of parts that went into the rebuild. All OEM. Injectors and injection pump were also both rebuilt at a certified Denso diesel injection shop.


Part NoDescriptionQty
13501-18010CAMSHAFT1
90999-73126BUSH(FOR CONNECTING ROD SMALL END)5
19850-58010PLUG ASSY, GLOW5
11213-18010GASKET, CYLINDER HEAD COVER1
11122-54020BUSH, INTAKE VALVE GUIDE10
11381-17010RETAINER, ENGINE REAR OIL SEAL1
90311-95008SEAL, ENGINE REAR OIL1
12261-17010HOSE, VENTILATION1
11011-17010WASHER SET, CRANKSHAFT THRUST1
11801-17010BEARING SET, CAMSHAFT1
13571-17010PLATE, CAMSHAFT THRUST1
13711-17010VALVE, INTAKE5
90913-02094SEAL OR RING, O(FOR VALVE STEM OIL)10
90504-49001SPRING, COMPRESSION(FOR INNER)10
90201-23003WASHER, PLATE(FOR VALVE SPRING SEAT)10
13715-17010VALVE, EXHAUST5
13741-54020RETAINER, VALVE SPRING10
90913-03014LOCK, VALVE SPRING RETAINER20
13751-54010LIFTER, VALVE10
17171-17010GASKET, INTAKE TO EXHAUST MANIFOLD1
17173-17010GASKET, EXHAUST MANIFOLD TO HEAD1
17179-17010GASKET, INTAKE MANIFOLD, NO.24
90917-06059GASKET, EXHAUST PIPE1
90189-04024GROMMET, SCREW(FOR GLOW PLUG)5
11177-64010GASKET, INJECTION NOZZLE SEAT5
11176-64010SEAT, INJECTION NOZZLE5
11328-17010GASKET, TIMING GEAR OR CHAIN COVER1
17115-17010GASKET, INTAKE MANIFOLD HOLE COVER1
11497-17010GASKET, CYLINDER BLOCK OIL HOLE1
15725-17010GASKET, OIL FILTER1
90311-58006SEAL, OIL(FOR TIMING CHAIN OR BELT COVER) NO. 11
90311-58007SEAL, OIL(FOR TIMING CHAIN OR BELT COVER) NO. 21
90430-22003GASKET(FOR OIL COOLER RELIEF VALVE)1
15785-66010GASKET, OIL COOLER2
96721-19010RING, O(FOR OIL LEVEL GAGE GUIDE)1
15149-17010GASKET, OIL STRAINER FLANGE1
15134-17010GASKET, OIL PUMP RELIEF VALVE1
15193-17010GASKET, OIL PUMP1
90430-20004GASKET, FOR PLUG ON OIL FILTER MOUNT NO. 22
90430-18008WASHER SOFT, FOR PLUG ON OIL FILTER MOUNT NO. 11
16341-17010GASKET, WATER OUTLET1
90915-30002FILTER SUB-ASSY, OIL1
11115-18010-03GASKET, CYLINDER HEAD1
11701-17010-03BEARING, CRANKSHAFT1
11701-17010-04BEARING, CRANKSHAFT3
11701-17010-05BEARING, CRANKSHAFT2
13041-17010-04BEARING, CONNECTING ROD5
13103-17010PISTON SUB-ASSY, W/PIN5
13013-18010RING SET, PISTON O/S 0.501
09275-54011PLUNGER STROKE MEASURING TOOL1
12361-17020INSULATOR, ENGINE MOUNTING, FRONT2
12371-17030INSULATOR, ENGINE MOUNTING, REAR NO.11
96411-42500PLUG, TIGHT, NO.111
96411-43500PLUG, TIGHT, NO.25
96411-44000PLUG, TIGHT, NO.31
96411-41800PLUG, TIGHT, NO.2(FOR CYLINDER BLOCK)4
96411-45000PLUG, TIGHT, NO.5(FOR CYLINDER BLOCK)2
15605-54010VALVE SUB-ASSY, OIL CHECK5
15708-17010NOZZLE SUB-ASSY, OIL, NO.15

1PZ Fan Shroud - $60 shipped - SOLD
IMG_1535.webp


1PZ to R151 Bellhousing - $150 + shipping
IMG_1540.webp


1PZ Injection Pump (Rebuilt) - $500 + shipping
Note that the power cable has a few areas where the insulation is worn through and some of the plastic power plug has cracked off.
IMG_1549.webp
IMG_1548.webp
 
Last edited:
1PZ Valve & Spring Set - $60 shipped
Used, taken off one of the heads
IMG_1557.webp


1PZ Valve, Spring, Guide, Cup, & Shim Set - $100 shipped
Used, taken off one of the heads. Almost a full set, missing one guide.
IMG_1560.webp


1PZ Head (Cracked) - $200 $100 (+shipping or local pickup)
A bit rusty and has a couple small cracks visible to the eye. Probably destined for the junk yard unless someone has a need for this.
IMG_1568.webp


IMG_1585.webp


PZ/HZ Starter 24V (28100-17020) - $50 + shipping
Was tired when removed from my 1PZ, needs rebuilt.
IMG_1591.webp
 
Last edited:
You must log in or register to reply here.

Share this page

Back
Top Bottom