oil pan gasket

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 18, 2006
Threads
137
Messages
992
Location
hillbilly desert rat
My oil pan gasket is leaking along one side and there is a small drip in the rear also.

1st: how difficult is it to replace the oil pan gasket?
2nd: can you replace the rear seal without too much fuss
3rd: what else should I replace while I am in there?

thanks for the input

D
 
You talking about the small lower metal oil pan, or the large upper alluminum oil pan? The lower one would be a breeze... maybe an hour to remove clean up and reinstall. The upper one is whole different can of worms. Probably take a day and half to two days if you've never done that job before.

:beer:
Rookie2

Edit: The above comments are for an 1FZ. I'm not sure if a 3FE has the same issues to deal with when removing the upper pan.
 
if you have a 91, then here's my input. First, there's a lot of info if you search.

1st: how difficult is it to replace the oil pan gasket?
Prying the pan off is the hardest part. Use a scissor jack from a domestic model and open the jack in between the pan and the driveshaft.
For your replacement gasket, get one that's a single piece. The gaskets at the chain stores are hit and miss as far as getting a single piece or getting one that's in four pieces. Or, just order from your local dealer. Trust me, I tried a four piece and the thing leaked worse.
2nd: can you replace the rear seal without too much fuss
If your referring to the Rear main seal, then No. You'll have to drop the tranny.
However, in the cases where I had to replace a pan gasket it stopped all leaks. Replace the pan gasket first, then worry about the RMS.
3rd: what else should I replace while I am in there?
I'd do the side cover gasket. i.e. the viewing place for the lifting rods.
 
Try and tighten your pan bolts before you undertake the replacement, My 2F stopped with a nice snug up of the pan bolts..
 
You talking about the small lower metal oil pan, or the large upper alluminum oil pan? The lower one would be a breeze... maybe an hour to remove clean up and reinstall. The upper one is whole different can of worms. Probably take a day and half to two days if you've never done that job before.

:beer:
Rookie2

Edit: The above comments are for an 1FZ. I'm not sure if a 3FE has the same issues to deal with when removing the upper pan.

3FE has one pan.

I've heard it's a chore and a half to get it down...
 
I'm doing this now on a 3fe and it is not too bad. Get some gasket spray remover/softener stuff and a small razor blade with a handle and a couple of chisel type tools to pry the old gasket material off.

To get the pan off I used a block of wood and the toyota bottle jack up against the frame. I tried the "apply moderate pressure and let it sit method" and it did NOT work. Maybe you will have more patience than I did. I ended up cranking the jack really hard against the oil pan/wood and increasing the pressure every minute or so and it finally popped off. This took about 30 mins. I didn't dent my pan any but becareful nonethless
 
Last edited:
To get the pan off I used a block of wood and the toyota bottle jack up against the frame. I tried the "apply moderate pressure and let it sit method" and it did NOT work. Maybe you will have more patience than I did. I ended up cranking the jack really hard against the oil pan/wood and increasing the pressure every minute or so and it finally popped off. This took about 30 mins. I didn't dent my pan any but becareful nonethless

I used the same method on two different 62's. Be prepared, when the pan finally lets loose it is like a bomb going off. You don't get any advance warning.
 
Back
Top Bottom