O2 sensor code 6 months after new sensors

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 7, 2005
Threads
303
Messages
2,353
Location
South Jordan, UT
I replaced my O2 sensors about 6 months ago as preventative maintenance. Got some aftermarket Bosch sensors. Yesterday I started getting code 21--problem with sensor #1.

This code appeared coincident with codes 83, 84, 85 --bad ECU. I replaced the ECU yesterday and all is well except for the O2 code.

I'm obviously not happy that I'm getting error codes from an O2 sensor that is 6 months old.

Could my code 21 be a temporary glitch that will clear after a little driving (I haven't driven anywhere since installing the new ECU)?

Could my code 21 be related to my use of non-OEM sensors?

If I DO have a problem with one of my O2 sensors, is it OK to still drive my 80?


Thanks.

Hayes
 
I replaced my O2 sensors about 6 months ago as preventative maintenance. Got some aftermarket Bosch sensors. Yesterday I started getting code 21--problem with sensor #1.

This code appeared coincident with codes 83, 84, 85 --bad ECU. I replaced the ECU yesterday and all is well except for the O2 code.

I'm obviously not happy that I'm getting error codes from an O2 sensor that is 6 months old.

Could my code 21 be a temporary glitch that will clear after a little driving (I haven't driven anywhere since installing the new ECU)?

Could my code 21 be related to my use of non-OEM sensors?

If I DO have a problem with one of my O2 sensors, is it OK to still drive my 80?


Thanks.

Hayes

I have aftermarket bosch 02's in my 94, no problems (see archive post). Did you use universal or harness plug and play type. One of the biggest issues I found with the universals was getting a translation to the color codes of the wires in the 93-94 feed from the ECU.

You can ck the 02 values per FSM at the diagnostic connector. I'd do this before test before anything else.

The truck will assign fixed values to 02 sensors if a code is present. The owners manual says drive to your nearest dealer.

You might also want to make sure you have properly functioning cats.

ST
 
I had a bad ECU code on my 92 FJ80, and it turned out to be a loose wire from the O2 sensors to the ECU itself. Once I made sure the wire was in place....no more O2 sensor codes, and no problems with the ECU.

Just a place to check.

-H-
 
A rich running motor because of the bad ECM or other things can carbon up an O2 quickly as well.

Assuming you have a 93 or 94 80 series because of the code numbers, you can pull the battery cable off to clear the code. If the code comes back, you have a problem.

The problem certainly doesn't have to mean a bad O2. It could be a host of other things.


To test the heated oxygen sensor, measure the resistance between +B and HT on the oxygen sensor. It should be 5.0 to 6.5 ohms at 68 degrees F. If it's not replace the sensor. If it is then the fun begins
 
Last edited:
Two months ago I had a code 2-8 (post cat sensor) this confused me.
Both my sensors are infront of the cats.
I soon came to the conclusion (with much reading) that in 93 - 94 there must have been some changes taking place during production.
This is why you have two diff sensors right and left but both sitting in the same position afront the cats. and coding as "main" and "post cat". Are they sampling for seperate parameters ? I don't know.
I now have a hard code 2-1 "main sensor" that I cant clear by pulling the EFI fuse.
My new sensors are in transit (from Cdan).
My truck is getting better fuel mileage, and running better right now running with the 2-1 code (in open loop mode-programed default settings) than it was for the last two months.
I can't wait for my new sensors
 
Check your connections since they are aftermarket. You could have one that got some moisture and the change in resistance is throwing it off.
 
Back
Top Bottom