nv4500 conversion

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 27, 2004
Threads
89
Messages
1,138
Location
North Platte, Middle of nowhere
Ok. So for reasons we wont go into, I am being put into high gear to replace my junk in the 40. Im thinking that the 4500 and a "new" 350 will be the ticket. I looked at the tech link for the 4500 conversion, but was looking for some input from those who have done it as to how long I might expect this to take. I dont know if I will be able to find a shop here who would do the work, so it will most likely be done in my driveway.

Also, what might I expect to pay for an adapter to mate to my Tcase, a new clutch assembly for the 4500, and any extra that I dont know about yet that I need to do before final assembly, of course keeping in mind that I will need my driveshafts shortened. Thanks
 
The adapter from the tranny to transfer case costs around $550.
The adapter to mate the front of the tranny to a Chevy bell housing is almost $300.

You can use a 96 up Chevy truck bell housing so you wouldn't have to buy the front adapter. But that bell housing uses an internal slave cyl, and there's no way to mount an external one.

The Dodge version of the NV4500 has a 1" longer input shaft than the Chevy version. With the 1" adapter spacer at the front it works fine with the earlier most common Chevy bell housings. And you can mount a slave cylinder as well.

I happened to use the Chevy version NV4500, a 96 up Chevy truck bell housing made for the NV4500 and a stock Chevy clutch ($140). But had to use an internal slave though.
 
I used the chevy version too, but used AA's bell housing to reuse the stock FJ40 slave cylinder. Everything brand new from the flywheel back to the adaptor I think I was 2900$ ??? I sold it about a year later for an auto tranny setup. Look below. Ended up with 1K in my pocket too.
 
What did you change to be able to use the internal slave? Is there any problems with using this type slave on the cruisers?

Side question, is the stock chevy clutch good enough to handle some stout offroad. I do mostly mud, sand, and water crossings. Or should I upgrade to a centerforce since I'm shelling out the bling anyway?

Thanks for your input.
 
The big disadvantage to internal slave is, if it goes bad, you must remove the transmission to change it. This is enough to scare most people.
I don't know how these internal slaves hold up to repeated river crossings.
At least not yet.

An advantage is there are no brackets to buy, special bell housings etc.
A little less guess work and trial & error on linkages, figuring release arm lengths, etc.
Plus you don't need to buy an AA adapter plate for the bell housing.

If you use a 96 up Chevy truck bell housing there will be a mount for the internal slave. Any year flywheel will work. I was told any Chevy 73 up clutch will work, but was also told to use a 96 up Chevy clutch because it has more release for shorter amount of pedal travel. I played it safe and got the newer clutch. A 12" clutch fit fine. If a 12" is big enough for a 2 ton truck, it's hard core heavy duty for a Land Cruiser.

I didn't like the idea of GM's plastic master cyl. I used a Wilwood 3/4" bore. Same bore as stock Toyota, but extra travel for increased fluid requirements. I had to have a custom hydraulic line made up. The GM clutch was cheap , as was the Wilwood master at $55. It acheives the same quick throw/release results for a lot less $$ than the centerforce clutch

I was amazed. It worked perfect the first time I tried it, no adjustments neccesary, and very light pedal pressure even for a heavy duty 12" clutch.
So far no regrets.
 
Back
Top Bottom