Noobie, reporting as ordered!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 15, 2021
Threads
8
Messages
22
Location
Washington, DC
Greetings! This is my first post, and I’m happy to join the global team. I’ve owned an FJ60 for several years and just purchased an HJ47.

Would love some tech advice on the HJ47. Specifically, I drove it for about 500 miles to get it home. It started really well all the way home, but now it turns over, but immediately quits. Any help?
 
Welcome! Pictures, year, and any troubleshooting you have done will help.
 
Welcome to the 40-Series section, your new home, mate! :cheers:
and as they say downunder...

don't forget that....jpg
 
Does the engine shut off a couple of seconds after it starts or will it not start at all?

If it starts then shuts off, firstly check the oil level. If it's got plenty of oil, ensure its got oil pressure. If it's low on oil or not getting oil pressure for some reason, the oil pressure switch will shut off after a few seconds.

If it's getting oil pressure, check the grounds, negative battery cable is the first place to start. Bad ground will make the edic act quite strangely. If the grounds all seem decent, the edic arm can be just pulled off the IP and the engine will start and run. Pull the lever back from memory to stop the engine or just stall ut
 
Does the engine shut off a couple of seconds after it starts or will it not start at all?

If it starts then shuts off, firstly check the oil level. If it's got plenty of oil, ensure its got oil pressure. If it's low on oil or not getting oil pressure for some reason, the oil pressure switch will shut off after a few seconds.

If it's getting oil pressure, check the grounds, negative battery cable is the first place to start. Bad ground will make the edic act quite strangely. If the grounds all seem decent, the edic arm can be just pulled off the IP and the engine will start and run. Pull the lever back from memory to stop the engine or just stall ut
Thanks for the reply! Yes, the engine shuts off a couple of seconds after it starts. Let me check the oil and such and get back to you. Really appreciate the assist. It seems odd that it was starting so well, even when really cold, the days leading up to the problem.
 
Thanks for the reply! Yes, the engine shuts off a couple of seconds after it starts. Let me check the oil and such and get back to you. Really appreciate the assist. It seems odd that it was starting so well, even when really cold, the days leading up to the problem.
Oil level appears full, but as black as night! Regarding oil pressure, I hate to appear dense and inexperienced, but what’s the best method of checking oil pressure?
 
Oil level appears full, but as black as night! Regarding oil pressure, I hate to appear dense and inexperienced, but what’s the best method of checking oil pressure?

Diesels run oil black within a couple hundred miles. I wouldn't be concerned about that, unless you see that the engine is consuming oil.
 
A mechanical gauge really is the best way to confirm that you have oil pressure. I have no idea where the ports are on this engine, but I'm sure someone who owns a 47 could help out there. If you are experiencing low pressure, it could be a bunch of different things like wrong oil, crap on the pickup, a worn out pump, etc.
 
As mentioned by AussieHJ above, check your grounds & such. Incorrect voltage, or intermittent voltage to your EDIC can cause it to shut the motor down pretty quickly also. There are two oil pressure ports on the 2H if I recall correctly. One for the actual oil pressure gauge, and a second for the oil pressure cutoff switch.

Clean up the terminals on both (again, goes to the concept of good grounds/connections). Although you could be dealing with low pressure, it is more likely a connection, especially if the truck hasn't been driven much lately until you took it on its road trip. Congrats on the new truck too!
 
As mentioned by AussieHJ above, check your grounds & such. Incorrect voltage, or intermittent voltage to your EDIC can cause it to shut the motor down pretty quickly also. There are two oil pressure ports on the 2H if I recall correctly. One for the actual oil pressure gauge, and a second for the oil pressure cutoff switch.

Clean up the terminals on both (again, goes to the concept of good grounds/connections). Although you could be dealing with low pressure, it is more likely a connection, especially if the truck hasn't been driven much lately until you took it on its road trip. Congrats on the new truck too!
Thanks a ton, SugarBear! I’ll work on this and report back. I used to live in Colorado Springs and Woodland Park. Where are you?
 
A mechanical gauge really is the best way to confirm that you have oil pressure. I have no idea where the ports are on this engine, but I'm sure someone who owns a 47 could help out there. If you are experiencing low pressure, it could be a bunch of different things like wrong oil, crap on the pickup, a worn out pump, etc.
Thanks, DangerNoodle! Will report back once I have news.
 
Thanks a ton, SugarBear! I’ll work on this and report back. I used to live in Colorado Springs and Woodland Park. Where are you?
we're in Boulder Canyon, a few miles west of Boulder!
 
Thanks a ton, SugarBear! I’ll work on this and report back. I used to live in Colorado Springs and Woodland Park. Where are you?

Such a small world. I'm about 20 minutes from Woodland Park. @cbmontgo is really close to me as well, and he has a 47. You still in CO?
 
Back
Top Bottom