noob EGR question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 26, 2007
Threads
33
Messages
267
Location
Bend , OR.
searched but did not find a good thread. I am looking at a 80 series, 97, lx-450, has a check engine light on with emissions code? 185k.

he says it is a EGR code and the EGR valve needs to be replaced.

My question is, is this a cheap part and will it fix the code? or am I looking at a modulator and wires and what not also?

thanks for this great board, it is like a landcruiser research paper that is never quite done.:D
 
There are posts here on troubleshooting EGR-related issues. Common causes are the Modulator (easy & cheap), clogged lines (easy & cheap), VSV (more expensive, and more of a PITA). Some have had to replace everything and use dental picks and other extreme measures to clean out passages.

Search for the posts. Best bet is to use the Pxxx code you're receiving via ODBII.
 
searched but did not find a good thread. I am looking at a 80 series, 97, lx-450, has a check engine light on with emissions code? 185k.

he says it is a EGR code and the EGR valve needs to be replaced.

My question is, is this a cheap part and will it fix the code? or am I looking at a modulator and wires and what not also?

thanks for this great board, it is like a landcruiser research paper that is never quite done.:D

People are going to probably tell you to do a search. Cause people don't like CELs around here. Mines on. Do you know what code yours is?

Cause I think there's a couple for EGR malfunctions and stuff.


Like mine's a code 71. And I've had it worked on twice. With no luck. At all. Super.
 
I spent a couple grand making my EGR code go away. The root cause can be a bit tough to determine.

Did you ever find the exact cause? I've spent about 500 and it's not worked. Code 71.

I think I'm going to replace the modulator or whatever the blue capped thing is.



What else is there to replace? I've checked most of the hoses and they're clear.
 
If you want to trouble-shoot the problem, a Factory Service Manual is indispensable. There's a thread about how to download it from Toyota for $10. Or you can order a printed one for about $100.

When I had my code, I read all the threads I could find, then ordered the Modulator and VSV from CruiserDan. One of these seems to be a common cause. Replacing the modulator was easy and solved my problem. Later, I got the VSV installed -- simply because I had it.
 
People are going to probably tell you to do a search. Cause people don't like CELs around here. Mines on. Do you know what code yours is?

Cause I think there's a couple for EGR malfunctions and stuff.


Like mine's a code 71. And I've had it worked on twice. With no luck. At all. Super.

I just fixed mine by chasing the wiring to the EGR VSV. On the 94 (and I suspect on the later trucks as well), the 12v+ power feed to a lot of the (ECU grounded) components is a 12guage yellow/red stripe wire that goes down the engine harness with a lot of crimp/tape junctions branching off. On the VSV plug (front DS of motor near distributor, grey square multipin connector), there are 4 VSV Y/R power wires (including EGR VSV) that join a single (narrow guage) Y/R wire, then join the main artery Y/R wire on the engine. All with just crimp and tape

I recrimped these two junctions using a larger guage branch wire, then heat shrink tubed them, and the EGR light and code went away. One of the crappiest engine wiring harness designs I've seen in a while. The harness routing by the EGR valve is next on my list....

HTH

Scott J
94 FZJ80 Supercharged
 
i am looking at a '94 and it was just in the shop for a CEL. the shop found a couple codes. 42-speed sensor and a 71-EGR. i've done a search and this is a common problem obviously. the question is.... would a 42-bad speed sensor trigger a 71-EGR. The shop says the EGR opens and closes based on readings from the vehicle speed sensor and that after replacing the speed sensor the 71 code went away and shouldn't return. Is this true? is the EGR related to the speed sensor or this a bunch of BS?

thanks for your input..... i gotta say, trying to find a decent 80 for the right price is no easy feat.
 
I just fixed mine by chasing the wiring to the EGR VSV. On the 94 (and I suspect on the later trucks as well), the 12v+ power feed to a lot of the (ECU grounded) components is a 12guage yellow/red stripe wire that goes down the engine harness with a lot of crimp/tape junctions branching off. On the VSV plug (front DS of motor near distributor, grey square multipin connector), there are 4 VSV Y/R power wires (including EGR VSV) that join a single (narrow guage) Y/R wire, then join the main artery Y/R wire on the engine. All with just crimp and tape

I recrimped these two junctions using a larger guage branch wire, then heat shrink tubed them, and the EGR light and code went away. One of the crappiest engine wiring harness designs I've seen in a while. The harness routing by the EGR valve is next on my list....

HTH

Scott J
94 FZJ80 Supercharged

Wow, very nice. I guess the 'grounding kits' that the ricers put on their cars isn't such a bad idea after all...
 
HANTS, where is the link for the downloading of the manual? Does anyone have a link? I dont see it on the FAQ.

Thanks!
 
Here's the link:

https://forum.ih8mud.com/showthread.php?t=128021

I just read the updates to the thread, and it appears that TIS has changed and Nator's scripts no longer work. :(

You can probably still download the sections manually, but it will be somewhat painful (many 10's of sections).
 
Back
Top Bottom