New throttle cable installed

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 28, 2004
Threads
72
Messages
1,101
Location
San Diego
I don't know why I waited so long. The acceleration is so much better now. There's a big difference before and after the replacement. The old original cable was worn and not looking so great. The sheath was severely worn in some areas.

For those of you that have been putting this off, wait no longer. Do it and feel the difference in acceleration responsiveness.
 
x2 on the details.

I've been putting this off a long time. Did you also clean the TB at the same time?
 
Did you do it yourself? If so, how long did it take? How much for the new cable? I've been putting mine off for a while.

Yeah, did it myself. Just dove in and completed the job in about an hour...maybe less. The toughest part was contorting myself to get under the driver side dash to remove the bolts. Removing the gas pedal makes getting to those bolts a little easier.

x2 on the details.

I've been putting this off a long time. Did you also clean the TB at the same time?

Will write up a short bit in a little while. Did not do TB.

Did you notice any difference in start up RPM?

No difference in the start-up RPM that I could detect. Then again it was after the weather warmed up a bit. Tomorrow morning would be the real test to tell about start-up RPM. Will report back on this tomorrow morning.

:cheers: :beer:
 
Throttle body? It isn't necessary to remove the TB when replacing the accelerator cable. Cleaning the TB is a separate operation.

To replace the cable:

1. Open the throttle on the TB, and remove the cable from the spring loaded butterfly fulcrum. Make the old cable nut positions for use when resetting the new cable adjustment.
2. From inside the vehicle, remove the cable holder from the accelerator cable, and the firewall. The pedal comes off, and makes it easy to change the cables.
3. From under the hood, unsnap the cable from the cable holders on the intake tube, vertical bracket on USPS of the head, charcoal canister bracket, and the brake booster mounted bracket.
4. From under the hood, slowly feed the cable through the firewall, into the driver compartment.
5. To install new cable, do these steps in reverse. (Be careful to not break the plastic clip on the cable)

HTH:popcorn:
 
Last edited:
When I replaced mine, I used an ODBII reader to ensure that it was within spec (both before and after).

After I removed the old one, I laid the old and new next to each other and set the adjustment nut as close as I could (yes, I'm OCD -- I actually counted the threads).

IIRC, the original read @ 8% via ODBII, and the new was 10%. I think the FSM said up to 12%, so I left it where it was.

I replaced mine after the 3rd or 4th time it stuck at WOT :eek: ... fortunately, I don't have forced induction!! :o

I'm pretty sure there's a writeup in the FAQ that I used.
 
The toughest part was contorting myself to get under the driver side dash to remove the bolts. Removing the gas pedal makes getting to those bolts a little easier.


I still have pulled muscles from doing that, and that was 18 months ago.

:cheers:
 
Throttle body? It isn't necessary to remove the TB when replacing the accelerator cable. Cleaning the TB is a separate operation.

To replace the cable:

1. Open the throttle on the TB, and remove the cable from the spring loaded butterfly fulcrum. Make the old cable nut positions for use when resetting the new cable adjustment.
2. FRom inside the vehicle, remove the cable holder from the accelerator cable, and the firewall.
3. From under the hood, unsnap the cable from the cable holders on the intake tube, verticale bracket on USPS of the head, charcoal canister bracket, and the brake booster mounted bracket.
4. From under the hood, slowly feed the cable through the firewall, into the driver compartment.
5. To install new cable, do these steps in reverse.

HTH:popcorn:

Couldn't have said it better myself :beer:
One thing I'd add is removing the gas pedal. That made things a bit easier... for me. I read about it somewhere around here. :grinpimp:


How much did the new cable cost?

The cable cost me $83.34. List price is $111.12. Courtesy of Dan. :)
 
Back
Top Bottom