New Headlights Very Very Dim

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 4, 2002
Threads
159
Messages
1,420
Location
Hiding
Well I got a new Bib assembly and some new headlights for the 40. By new I mean new to me, but still the old school style. I installed them this weekend and made the new connections. Soldered everything in. Good grounds etc.

When I turn the lights on they are VERY VERY dim on low beams. I mean almost non existant. When I hit the high beams though they look fine. Well the driver side looks fine, and nice and bright. the passengers side does not work on High beam.

I will preface this by stating its a 1971 wiring scheme with two harnesses coming from the fire wall on each side.

Any Ideas about the dimness? I am still reworking wires cut by the PO.
 
Good time to install relays. A relay will usually even brighten headlights that weren't dim.

GL
Ed
 
I would say yes, they were working good before I switched them. The PO had a snow plow at one time so after cutting out 20 feet of extra wire and BS. I am back to stock.
Funny thing though. The driver side headlight worked fine the old way. Good Low and Hi beam. The passenger was always dim.

Now since the new bib, and reconnections, both driver and passenger are dim on Low. Driver is good on Hi, Passenger does not do anything different on Hi.

Any more guesses.

By Bypassing the switch do you mean, leave the ground wire alone and run one wire say from the Green orange wire directly to the +battery cable? I understand that part.

as far as relays, please explain more thanks warren.
 
Well a relay is a switch that is under the hood and connected with a big wire to the main power source, ie the battery and another big wire to what you want to run, in this case the lights. Then the wire from your light switch also goes to the relay to activate it. Your horn already has one. I mounted one for my HEI.

http://www.madelectrical.com/catalog/rly-1.shtml



Pretty good site for wiring info.

GL
Ed

After reading all that info, go to your local autoparts store and pick up a 30 amp relay for about $6. Actually, you'll need 2 one for low and one for high.
 
Last edited:
zetasig said:
I would say yes, they were working good before I switched them.
Funny thing though. The driver side headlight worked fine the old way. Good Low and Hi beam. The passenger was always dim.

Now since the new bib, and reconnections, both driver and passenger are dim on Low. Driver is good on Hi, Passenger does not do anything different on Hi.

Any more guesses.

Check and make sure the bib is well grounded. Maybe run a grounding strap to the frame.

A voltmeter would help you quite a bit in narrowing this down.

Kirk
 
I agree on the voltmeter usage, as you may have pinched a wire some with the new bib somehow and you have a partial voltage drain. Measure what the voltage is at the lights. Ought to be pretty close to 12v, higher if its running. What's the voltage at the light switch? You may have loosened a crappy connection by jacking around removing all the extra wiring and now you've go a fully engaged crappy connection.
 
The bib may not be gounded well but both white/black ground wires are good. So even if the headlights are grounded, the bib should be grounded too?

The only place the bib is really grounded to the frame is the bottom hinge, Two bolts running in and one coming from the bottom up.
 
Just build a new head light harness . You have 2 weak links in the lighting system the 14 awg wire and the connector at the light switch. I just finnished doing that yeaster day. It cost about $40 to do it. Run 2 relays . Use the stock wiring to provide the power to open and close the relays. This does not put a big demand on the stock wiring. This set up pulls power off the battery to power the head lights. It is a simple job. Send me a message if you need the parts list and a step by step.
 
I forgot to say that you can buy this set up from SOR but it will cost you about 3X the amount. I hate to pay someone for something I can do myself. I don't think the bib not being grounded will cause you any problems because the head lights have there own ground through the harness. you should be able to pull the light and just plug it into the harness and it should work just fine holding it in your hand. As for the pass light you may have a cold solder on that pole.
 
Back
Top Bottom