New engine sound . . .

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 9, 2006
Threads
109
Messages
2,152
Location
Sandy Eggo
. . . to me.

The LC just developed a knock type of sound. I noticed it this morning. Sort of sounds like someone rapidly tapping on a hollow piece of bamboo:confused: . I've heard knocks and taps from spun/bad bearings, but this is nothing like anything I've heard before.

Location is within the front center of the oil pan (used a long piece of hose to find it). I have an FSM on order, but in the meantime, any idea what this could be? Dreading a bearing problem.
 
Land,

I can't believe I'm saying this, but I fear you could be right. How many miles? How long has this condition been there? Are you positive it's coming from the lower end?
 
DTAYLOR said:
Land,

I can't believe I'm saying this, but I fear you could be right. How many miles? How long has this condition been there? Are you positive it's coming from the lower end?
Ew.

I just noticed it Monday morning, but that's not saying it hadn't been there a while. If you look at the cast part of the oil pan, there is a small circle in the center of the casting. Right about that spot is where the noise was loudest (w/ the makeshift stethoscope).

The LC just turned 106k.
 
Check Skillet's thread. It has quite a few suggestions on what could be causing a similar sound.
 
i have the same sound too....i am ready to go up to the shop and look inside the motor...cylinders 4/5 making the sounds in the low end....the new short block just arrived too....it is cheaper for me (in the middle of nowhere without a machine shop to do the rebuild)...the thing is, mine only has 64,000 miles...i will keep you posted once the final diagnosis is made
 
After taking the oil pan off, going through all kinds of crap I found the problem - the pully behind the harmonic balancer has delaminated from the rubber bushing.

The pully for the belt and harmonic balaner are made with a piece of rubber to act as a cushion I guess, so the pulley part just turns freely by hand now - this is for the 1HZ engine BTW, not the 2F - but they might be the same type of pulley.
 
No idea. Sound is still there; no better, no worse. :meh:
 
Oil pump possibly.
 
No idea. Sound is still there; no better, no worse. :meh:

OK...mine has the same noise but only when the front end is lower than the rear. The noise goes away when level or the front is up an incline. :confused:

Anyone figure out what this noise may be???
 
Vista,

Both my current 80s do this and so do others I've heard when nose down on trails. It's kinda subtle - a gentle rubbery rattle or distant tapping, right? If so, I've decided it's simply part of the 80s engine sound - perhaps some end play in the connecting rod/crank journals or oil turbulence with the dual oil pan setup designed to prevent oil starvation at extreme angles. IIRC it only does it in neutral/park when the engine's unloaded - not in D when the engine's loaded a bit.

So to clarify, I've heard this 80 sound since 1992. Don't sweat it.

DougM
 
Vista,

Both my current 80s do this and so do others I've heard when nose down on trails. It's kinda subtle - a gentle rubbery rattle or distant tapping, right? If so, I've decided it's simply part of the 80s engine sound - perhaps some end play in the connecting rod/crank journals or oil turbulence with the dual oil pan setup designed to prevent oil starvation at extreme angles. IIRC it only does it in neutral/park when the engine's unloaded - not in D when the engine's loaded a bit.

So to clarify, I've heard this 80 sound since 1992. Don't sweat it.

DougM

Distant tapping from the front of the pan would be a pretty accurate description. Glad to hear yours and so many others have been doing it for a while. I feared bearings, crank or something else that might require an engine rebuild with only 99k on the clock.
 
Vistataco said:
OK...mine has the same noise but only when the front end is lower than the rear. The noise goes away when level or the front is up an incline. :confused:
That is exactly my scenario!
 
Back
Top Bottom