Need help with shuddering

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 8, 2009
Threads
179
Messages
1,784
Location
Western Carolina
Ok, so I have been chasing a rattle in my engine on my 95 FZJ for some time now to no avail. The other night on advice from a lexus mechanic, I unbolted the torque converter from the flex plate and ran the engine to isolate the noise. We put the torque converter/flex plate back together and now the entire truck shudders in park, especially when the A/C is on. I know the bolt with the shoulder has to go in first per the FSM but I took it apart again tonight and did that, still shudders. Any ideas/thoughts/wisdom?

Is there a matchmark for the torque converter/flexplate that needs to be lined up for it to be in balance?
 
Yes Sir there is. You have to aline it.

Hopefully you did not damage the seal or the bearing by mis alining it. You could have alined it right but mistorqed it cuasing the flex plate to shift when you ran it.

Take the starter out realine/bolt torque coverter on and spin it. Look for damage to anything.

I broke one once ... sux hope this helps

Squirrel
 
Ok, so you take the starter off, and spin the flex plate? That is attached to the crank isn't it? Or do you spin the torque converter? I am slightly confused.... I can spin the torque converter from the inspection plate on the oil pan, where is the alignment?
 
Sorry for the confusion, the starter is removed so the bell housing can be removed for inspection. The transmission should be moved aft approximately 4 inches for proper inspection. Verify that the flex plate is not damaged (cracks, bent, ect). Inspect the torque converter bolt mounts for damage. Do not remove the converter from the transmission as this will make a mess and can possibly damage the seal $. If you like you can install the starter with the transmission separated and start the engine to se if the problem persists. Look for any kind of alignment marks or stamps before you put the mess back together. Reassemble the components if there is no damage. Hope this helps....
 
Day late and a dollar short, the seal blew today, so it is going to the shop to get fixed. I asked if they'd look at the flex plate and see if there are any cracks or such to rule that out as a rattle issue. Are the flex plates balanced? I know they have little dimples drilled into them, but I don't know if that is true " balancing" or just counterweight for the crank.
 
Seal blew??? rear main or converter seal?? That really blows.
That is why a experienced tech always mark the flywheel to converter if it needs to be put back together again.

I've had cracked fly wheel in my acura legend. it made metalic ticking noise for a while and it completely broke off from converter. I hope you'll find and fix the problem.
 
Not sure about the flywheel balancing, sorry to hear about the seal. We live and learn. I have busted a part or two in my short time on this earth. I will tell you one thing ... after reading this I'll be sure to mark my converter position for sure before separating from the flywheel of my 80.
 
Seal blew??? rear main or converter seal?? That really blows.
That is why a experienced tech always mark the flywheel to converter if it needs to be put back together again.

I've had cracked fly wheel in my acura legend. it made metalic ticking noise for a while and it completely broke off from converter. I hope you'll find and fix the problem.

It apparently was the converter seal, it has been ticking for a while, if it is a flex plate i'll be pissed as I just junked one on my old block which was fine (the flex plate that is)

Not sure about the flywheel balancing, sorry to hear about the seal. We live and learn. I have busted a part or two in my short time on this earth. I will tell you one thing ... after reading this I'll be sure to mark my converter position for sure before separating from the flywheel of my 80.

Fo Sho
 
Back
Top Bottom