Nearing lift time

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 19, 2008
Threads
105
Messages
787
Location
Boone, nc
I know there are a ton of posts on this and i have seached for months and sent out lots of pms but, its nearing the time when i'll be doing my lift so here are my questions. Thanks for the hlep!

The questions are mainly for people who have medium ome springs in the front of their rigs. I have pretty much decided that i will use the mediums in the rear ( second row seats drawers behind them that weight at most 150 loaded )

Do the mediums in the front offer you up the advertised 2 - 2.5 inches of lift? ( i am completely stock in the front)
I dont really want to go up to the heavies, but if the mediums in the front dont really do what they say they do i guess i'll move up.

I dont mind a little stink bug, and as i said i do carry weight in the back on a regular basis.
 
put mine in last week. I do have a little stink bug action. I will try to measure later tonight. I did not measure prior to the lift.
 
Last edited:
that would be awesome thanks man
 
I believe OME says the front will lift 2" and the rear will lift 3", so most folks average it into a 2.5" lift. I have the mediums front and rear. I measured centre cap to flare last year and I remember it being a difference of 2" in the front and 3" in the rear (no third row). There was no added weight to the truck at that point. So I did get the amount of lift they advertised.

As a point of interest, I put sliders and a skidplate on this summer (and removed the spare tire and hoist) so I just went out and remeasured the distance. I'm now down to 1.5" in the front and 2.25" in the back. I think when I add a York and dual batteries I'll probably switch to heavies in the front.
 
When I put my springs in they were well broke in.

2" lift front, 2.5" rear (almost exactly).
 
I am also completely stock in the front and running the medium springs. I took before-and-after measurements from hub to flare and got the following:

Stock:
L - 19.75"
R - 20

OME:
L - 21.75"
R - 21.875
 
Cool, really helpful info! So are yal that put the mediums on are you happy with them? Or, would you rather go with something else?
 
Cool, really helpful info! So are yal that put the mediums on are you happy with them? Or, would you rather go with something else?

I like mine but I do have some stinkbug...I believe this is why the 850/860 combo is popular, for a more level stance.

Even fully loaded for a wheeling trip, I still had some rake. But I don't have a lot of heavy accessories. (Yet :D)
 
I'm quite happy with the mediums. They were great on an otherwise stock truck, and they seem to ride even nicer with the extra weight I've got on now. I can't compare to a heavy/medium combo however as I've only had the one set up thus far.
 
Cool, really helpful info! So are yal that put the mediums on are you happy with them? Or, would you rather go with something else?

Boone Im really glad I chose the heavys (850's).. the mediums would have sat to low...and they have the same spring rate, heavy's give about .75 inch taller than med.

This pic shows what you get with medium rear (860's) with 2nd and 3rd rows out, no hitch or running boards, it gave me 3.5 inch over stock springs... sorry this pic is cut off a bit..but you get the idea.

Scott
IMG_0584.webp
 
Thanks for all the replies, i know this is a well covered topic so i appreciate not getting flamed relentlesly.

Since my last post i actually located a set of rear mediums that i'll be getting from another board member.

Since i will have some weight in the back i think they will end up settling down to a reasonable height.
I do think that i'll be going with the mediums front as well (unless someone can give me a really good reason not to.) I dont mind a little bit of stinkbug so hopefully i'll be a member of the lifted 80 club before too long.
 
Back
Top Bottom