MAF Spherical Rod Ends

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 19, 2007
Threads
46
Messages
628
Location
Greenville, SC
I'm buying the 4+plus rear adjustable Panhard from Man-a-Fre, but don't need to adjust the front. I'm just gunna replace the bushings. So I need to know where MAF Buys the Chrome Moly Spherical rod ends for those panhards? I can't find any like them anywhere. Also, what about the rear control arm ends? I want those too :D

Thanks in advance for the help!

-Josh

80rrpanhardrod.jpg
 
I'm buying the 4+plus rear adjustable Panhard from Man-a-Fre, but don't need to adjust the front. I'm just gunna replace the bushings. So I need to know where MAF Buys the Chrome Moly Spherical rod ends for those panhards? I can't find any like them anywhere. Also, what about the rear control arm ends? I want those too :D

Thanks in advance for the help!

-Josh

80rrpanhardrod.jpg

It won't work, because the mount won't be designed to hold the joint inside. The MAF setup can only press in one side to a certain point and is held in by a c-ring.

If you want to do the rear, buy and tap some DOM and use a threaded heim joint on both ends. You'll pretty much need to buy the front unless you want to get into some serious fab work.
 
It won't work, because the mount won't be designed to hold the joint inside. The MAF setup can only press in one side to a certain point and is held in by a c-ring.

If you want to do the rear, buy and tap some DOM and use a threaded heim joint on both ends. You'll pretty much need to buy the front unless you want to get into some serious fab work.

x's2 you took the words right out of my head....
 
s*** ... I just remembered that. I'm sorry, dumb questions I asked without thinking .... :doh:
 
Ok, so let me try and save this thread ...

What about the Johnny Joints that Currie sells? If I buy a 1" rod end type, will push in my stocker front panhard. Besides, polyurethane and polyester, what other types of ends can I push in my stock arms? :cheers:

ce9112.jpg
 
pimp!
 
It would be sheer luck to have those things fit your mounts and bolt sizes. To my knowledge, nobody has found ones that fit even for the control arms.

JJ's are a great application for a panhard, if you can make it work post it up :D

Or just buy the Slee rods and be done with it and save some coin over MAF. I'd have no hesitation running the Slee rods with blue bushings, they are a proper bushing design unlike you OME's and won't shred.
 
I know, I was looking at the slee fron, but I honesty want that spherical end with rubbers. I guess I could just put rubbers in the slee panhard. and then paint it black ... I couldn't find a johnny joint 1". 2" inch is the smallest they have, at least on Currie's site.
 
Put new rubber in your stock front and leave it alone. Get the MAF rear and you're done.
 
I think that's what I'm going to do.

Ok, another question ... prefably for Nay ... :)

I put those POS OME Bushings in the rear of the front radius arms. Those look like around 2" with about a half inch bolt size? Could I go JJ's with those, and get a little flex, or do the ends need more strength? I'm sure those JJ's are stronger than OE rubber ... What do you think?

Thanks again
 
I think that's what I'm going to do.

Ok, another question ... prefably for Nay ... :)

I put those POS OME Bushings in the rear of the front radius arms. Those look like around 2" with about a half inch bolt size? Could I go JJ's with those, and get a little flex, or do the ends need more strength? I'm sure those JJ's are stronger than OE rubber ... What do you think?

Thanks again

You don't need a JJ on that bushing, the flex is limited by the required compression of the two axle end bushings. Go back to rubber or the Slee blues would be good - I have them for caster correction and so far am liking them.

Having said that, JJ are a great bushing on that end of a radius arm because of the rigidity, so if you could fit one it would be a nice feature. The problem with any standard bushing is the twist it enables also means it can deflect, and deflection on the road = slop. This is why when people 3 link and lose the side to side bind they go JJ on all the ends. If you don't need deflection to assist with link bind, there is no value in a lot of bushing movement. You just want rotation.

But again, not an issue on the 80 front end. Same reason you really don't need a spherical end in the panhard up front, even though I think there are some small benefits (less rubber, no contribution to an already bound front end).
 
Last edited:
Yeah, I agree ... I might measure and see if I could find something that fits, just for s***s and giggles ... I'll probly run rubbers back in the panhard until, I feel like giving MAF $500 ... :bang: The core just kills you ... Thanks man!
 
Back
Top Bottom