Luke's Hysteer

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 6, 2005
Threads
59
Messages
1,155
Location
Menlo Park, CA
I have a 76 with stock front axle (small knuckle pattern)

I need to get hysteer on my rig. I am not planning on wheeling it hard. I will go to Rubicon 1-2 times a year and other trails in Cali.
Rubicon probably being the hardest of the ones i go to.

I'm not hard on my rigs at least with this one I'll be taking easier lines and not "flogging the chit out of it". Eventually I'll get an ARB in the front. that way i can unlock it on turns causing less stress on steering.

With this said, Is it really necessary to switch over knuckles, and whatever else goes with that process? Or should I just purchase the kit for what I have now and enjoy?

Yes I have read the FAQ's
 
If I were in your position, I would get the larger pattern knuckles, the ARP stud kit, do it once, and be done with it.....but that is just me....


In the event that you decided to upgrade later, it is going to cost you the same monies in parts and labor to redo it, as you cannot simply "drill out" the old arms to the new pattern.



Good luck!


-Steve
 
I know I'm going to be told to read the FAQ..... but besides replacing the knuckles what else needs replacing??

Do my stock birfs and axles fit with the later knuckles?

I'm going to go back and read some more FAQ's now...
 
The only parts you need to change to do the knuckle change is the knuckles and the lower trunions.

IMO It really is best to just do it.

A knuckle would be a really bad weakest link. Hard to trail fix.

Ask Luke. He's a nice guy and would be happy to give you his much more knowledgeable opinion.
 
So.. the knuckles, lower trunions, and ARP Knuckle studs are all I need. Great.

So for now i can do that, and if I desire to get some longfields later down the road all I would need to do is grind the housing down a bit to accept the larger birf correct?

Some of those FAQ are a little confusing by the way.
 
yzftaco said:
So.. the knuckles, lower trunions, and ARP Knuckle studs are all I need. Great.

So for now i can do that, and if I desire to get some longfields later down the road all I would need to do is grind the housing down a bit to accept the larger birf correct?


Yep. It would probably be easier grind the opening for the birf when the knuckles are off however...


yzftaco said:
Some of those FAQ are a little confusing by the way.



Please elaborate on this,(provide the confusing links) either here, or in a PM and I will try and get straitened away!


:beer:
 
On the Hysteer link: FYI

these two are the same post:

Steering knuckle differences

More steering knuckles


I'm just a noob when it comes to the lingo so it's a little confusing to me. Like I'm not sure what a Trunion is :rolleyes:

In one post of the above links, one guy is contradicting himself:

tornadoalleycruiser said:
So you can use a 79 birf with a 76 lockout by using fender washer and bolt

Can't use 76 lockout on 79 birf tho.
 
You know what it is now?


Knuckle bearing/trunion bearing = same deal...


Trunion cap...lower knuckle bearing mount....as the steering arms form the trunion cap on top. :)


Will fix the links in a bit!

THANKS!


-Steve
 
Got it...

Thanks Steve!

I have no problem tearing $hit appart, wrenching, rebuilding, whatever

I'm just bad on the terminology

I'm more like... that thing-a-ma-jig bolts up to this thingy and so on. OK I'm not that bad... but there is a lot i dont' know!
 
Steve.. I don't surf as much as I should but gotta pn on the ARP studs? or where to buy em? Doubtful my local guys will have or know nuttin bout what I'm askin. No hurry, heading to Chef's for the weekend for some FJ40 deconstruction.
 
Fyi

I am in the process of finishing up this conversion, and when I spoke to Luke about the ARP bolts he recommended the updated Toyota studs. He gave me the parts #'s and was very helpful throughout. The new style studs have a star pattern on the end for easy install. One mistake that I made was when I bought new cone washers (they are definately different than the samll patttern) I bought them for the bottom too because that's what I had on the old knuckles. Mini truck knuckles don't have lower cone washers though. I had the trunion caps when I ordered the cone washers yet never made the connectiion. :doh:

Clint
 
The new Toyota studs are just as soft, and will fail just as easy as the originals....have seen it too many times.


I would not run stock studs in a hysteer application knowing that there is another fastener out there that is far and away stronger....but that is just me....to each their own.


:beer:
 
Back
Top Bottom