locker for fj80

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 12, 2008
Threads
2
Messages
4
Hey everyone, I am looking into putting a fj-80 axle in the rear of my samurai. Does anyone have an opinion on what is the best year and configuration? I would love a spool, but have heard that it is not available. I would like to be able to swap out rear shafts quickly, so a lockright is not ideal, but if I have to I will. What else is available? Also, it seems that they came in fullfloater locking, fullfloater non-locking, and nonfullfloater non-locking? IS this true and is the nonfullfloater even worth looking into? Thanks for any input. Have a great day, Don
 
Don,

Full Float is the best. I am putting one in the rear of my 91 (came with a semi-float). The e-locker version is only available in the full float. (93 and newer) I have a semi-float (91 and 92) I will sell you if you really are interested in it. :) I have been running my Aussie locker in the rear of my semi-float for about a year now and I like it. I have not had a problem with it. I would seriously doubt you would break an FJ80 axle in your Sami. On that note the semi float axle shafts are thicker but more difficult to change / carry a spare. The full floats are thinner, but easier to swap.
 
How much time will it spend on the road?

What is the engine?

And an 80 rear is WWAAAAYYYYY over kill IMO for a Sammi.

I'd go Mini since they can handle 35's pretty easy they are common and a hi pinion would bolt in once I found one. Parts and support should be cheaper as well.

But hey to each his own. Never on highway? I'd spool it. Since it replaces the carrier and would be much stronger. And a lunch box locker is a glorified spool anyway.
 
Thanks for the replies everyone. I never drive this rig on the road. I have run a hybrid sidekick/sami rear for years. I recently participated in RCrocs in PA for a rockcrawling series and had an issue with my rearend. For the series I need to keep a stock front axle housing, but the rear can be swapped out. After this series I was going to swap in a set of FJ80 axles for strength (I have replaced front axles and birfs so many times I've lost count) so I figured I would get half way done and swap to an fj80 rear now. It is important that I can swap out shafts fast so the fullfloater sound appealing. So with this being the case, it sounds as if the fullfloater is what I should look for, but what are my options for spools or lockers with this specific axle. Thanks for the input everyone. Don
 
There are some decent lockers out there, factory e-locker, ARB, Aussie (Lunch Box), Detriot. One thing to note is that if you get the e-locker full-float and you break the axle shaft in the housing you will not get it out.
 
Is their a Full spool available for that rear?...I think not but I'm not sure.


And if not, I'd check w/ some Aussie companies. I've seen loads of stuff there, but no vendor for them here.
 
No spools. Also you do know that the Land Cruiser rear is a passenger side drop third member, right?
 
FWIW,
The 91 92 semi float rear can be had for pretty cheap, No real advantage over a 60 series housing other thant he width. But if you read toyota trails, last issue they put a mini spool designed for a chevy axle housing in a 40 series rear, as far as I know, You could do it to a semi float rear 80 housing as well.
Dave
 
Thanks everyone. Yes, the passenger drop matches up perfect with the Sami. It sounds like the most reliable easiest to work on set up is going to be a fj80 full floater with a detroit locker even though that spool in the semifloater sounds tempting. I really appreciate everyones input. I definately do not know alot about Land Cruisers so this is great info. Thanks again. Don
 
Back
Top Bottom