little problem here

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 14, 2006
Threads
89
Messages
868
Location
Woody P
Well just got finished with the rear end lift and before I start on the front I need to know what I need to do about this, I know I need a longer driveshaft (ha ha) but where the heck do I get one? The only reputable 4x4 shop in town doesn't really deal with foreign vehicles so I don't want some hack job put on. Do any of you guys have a fix for this laying around?View attachment 74123

View attachment 74124

Or is it no big deal? And any 4x4 shop will be able to take care of it? Thanks fellas
 
Last edited:
lengthening a drive shaft is pretty simple, I would go to a shop that specializes though.

Good luck! :D

BTW, nice looking lift.

Rezarf <><
 
Looks like you've got a questionable amount of spline engagement. If the the driveshaft is in good shape, look into having it lengthened at a driveshaft specialty shop. My experience is they will charge you a bit more for the metric tube, otherwise, no different than working on any other driveshaft.

Cheers, Blake
 
My buddy has done a few front ones for his Heep. They are the right length but he is having issues with the tranny swap he did and the yoke clearing the pan (not failures). Any shop that specializes in driveline work can do it. and his were cheap, I think $45 to have the turning, welding and balancing done.

GL

Pete
 
find out how much they want to retube it. if its more that a reasonable amount, we can exchange measurments. mine had a 4" kit before i started "the project" :rolleyes: and I have about 7 drive shafts takeing up space in my garage. i want to say the po had new ones made just before i bought it. just pay the shipping and its yours.

send me a pm and we can exchange measurements if you like

mike
 
Driveshaft lengthening and shortening are ubercommon amongst wheelers, so I'd ask around locally with 4x4 clubs to see who people recommend. Around here (Seattle area) the prices vary considerably. The local 'professional' driveshaft shops would charge about $120 to lengthen a shaft, and about $85 to shorten. Then there's a one-man shop run by a guy with a built Samurai that did mine (one shortened, one lengthened) for $100 total.

To shorten a shaft, they cut the tube off at the flange, cut it to length, then re-weld it and balance it. This cost me about $35. To lengthen, the tube has to be cut off at both ends, then new tube is welded in and then it's balanced. This cost me about $50 + $1/inch of tube.

For competition rigs, it may be worth spending more or custom ordering from Wood's or one of the other specialty vendors, but for normal use, I wouldn't pay much more than the prices I listed above. If you can find a place that's cheaper, count yourself lucky.

Just my $.02,
Eric
 
just thinking outloud, but isn't the front driveshaft longer? Maybe a little swappie swap might do the trick... anyone?

Rezarf <><
 
Very easy to do (assuming you have stock drive shafts measuring around 1.56" OD or so, and welding skills):

1) Determine the length you want from yoke to yoke.
2) Cut the shaft in half. Since you are lengthening, the old shaft will become plugs for the new shaft.
3) Measure and cut a chunk of 1.75 OD x .083 wall thickness tubing to fit just short of the welds on the tube you cut in half. I found mine at a truck parts store that also built driveshafts for diesels. It isn't cheap.
4) Slide the old shaft "plugs" into the new shaft. Mine were a little loose, so I used 4 pieces of mig wire to center the plug.
5) Align the yokes before you weld (don't ask me how I know).
6) Check your alignment - make sure everything is straight - this will involve a little shimming of your work surface.
7) Tack weld at 90 degree intervals.
8) Double check everything again.
9) Weld it up - I'd suggest welding about 45 degrees, and then move to the opposite side - kinda like tightening the lug nuts on a rim.

I've done that to two sets of drive shafts now and haven't taken them in to be balanced - may help a little, but I don't feel enough vibration to be concerned.

HTH.
 
Driveshaft place or your local Machine shop can do it easy.

Personally if it was a daily driver i would get it balanced if you do it yourself like trainrech says. I have seen allot of guys try this only to blow u joints like crazy, I even had a buddy wreck a double cordon on the way to an event and only noticed a vibration and by the time we came out of the bush and back down the highway blew it apart so much that it cracked the transfer case.
 
Back
Top Bottom