lisense plate lamp wire

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 13, 2012
Threads
69
Messages
553
Location
fort smith, arkansas
would someone be so kind as to give a brief explanation, or even a picture, as to how to route the power for the rear plate lamp on my 67/40. I have to replace the lamp on mine and the power wire just comes out from underneath the truck and goes to the lamp, free hanging, and gets pinched between the door and the rear sill :rolleyes:.
 
Is this a soft top model with tailgate? If so the wire went thru the Gap at the bottom of the license plate bracket then thru the middle of the sill directly below that. There is a rubber grommet to protect the wire. From there it wired in to the harness heading to the left tail light. It share power with the left tail light not brake/turn signal. @Coolerman has all the bullet connectors needed to do it correctly if yours have been cut off.
 
no its a factory hard top model. there is a spot on the inside of the door where it looks like a wire is supposed to run through. just not sure where it would go after that, either under the cab or into the fender I assume.
 
To avoid pinching your wire will have to cross the same pivot point as the door hinges. If they are barn doors it will go through the barn door and then across to the nearest wheel well. From there it can connect with the wire that powers your rear side marker. Don't take that as a gospel purist wiring diagram though, That's just how I did it. Should come on with the running lights circuit.
 
no its a factory hard top model. there is a spot on the inside of the door where it looks like a wire is supposed to run through. just not sure where it would go after that, either under the cab or into the fender I assume.


You confused when you said rear sill. Hard top barn doors should have a couple metal clips to hold the wire and keep it from sagging. Then a grommet on the top of the wheel well at the very back. If you clips are gone going to be hard to keep the wire from sagging.
 
You confused when you said rear sill. Hard top barn doors should have a couple metal clips to hold the wire and keep it from sagging. Then a grommet on the top of the wheel well at the very back. If you clips are gone going to be hard to keep the wire from sagging.

thanks this is more or less what I needed to know. I wasn't aware the wire was just out in the open like that. like I said the PO did something stange and im not sure why. the wire runs out of the lamp, and around the sill to the underside of the truck, and ties into the trailer wiring he had installed. im in the process of removing all of the trailer wires also.
 
thanks this is more or less what I needed to know. I wasn't aware the wire was just out in the open like that. like I said the PO did something stange and im not sure why. the wire runs out of the lamp, and around the sill to the underside of the truck, and ties into the trailer wiring he had installed. im in the process of removing all of the trailer wires also.


You need any pictures in particular let me know. Have a 9/67 and 10/69 hard top models.
 
Thanks for the help guys. I spent the better part of 2 hours removing TWO old sets of trailer wire harnesses, splicing and fixing my original wire harness, and getting the tail lamps and plate lamp all fixed up. No I need to add in a reverse lamp I guess.
28028077-A79E-4E8B-943D-CB2E40008E6B.webp
72C7683E-1A77-47DC-B85C-9C4412A865D1.webp
D07065D1-1DC4-4C2D-ADF3-52738F12C24C.webp
49FC972A-A2AD-4C25-A796-063DE4E7AAC3.webp
 
Thanks for the help guys. ... No I need to add in a reverse lamp I guess.

Looks great. I like the look of that mesh wire loom better than the corrugated split loom. Looks like you ran it exactly the way I had it in my head. I switched from barn doors to a drop-down tailgate, so I had to run mine down and through the rear sill instead.

Count yourself lucky. The reverse lights thing is a current pain point for me. The wires coming off the switch on the transmission are missing on my truck. I may need a whole new switch, but haven't been able to test it yet. I am scheming if I can just replace the whole unit without removing the transmission tunnel. I think it will be a little bit like using a scope for surgery to get it out from underneath. I can reach it with a socket, I just don't have a replacement switch on hand.

I am debating whether I risk taking it out to test it (or if I can test it without removal), re-soldering leads (if it works, but would need to be removed for repair) and re-installing. If it doesn't work, then I don't want to put the bad one back even temporarily to plug the hole. I don't expect it will be easy AT ALL to get out or back in when approaching from under the transmission tunnel. I'm not sure I can drive it without something in that hole (I don't think I can) and I just got my truck back on the road, I'm not ready to have it parked again. I'll think more about it another day.
 
Back
Top Bottom