knuckle grinding?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 9, 2006
Threads
25
Messages
281
Location
Chattanooga TN.
so, i'm trying to get 85 birfields into my 75 landcruiser, I ground the area so the flats would slide in fine, but now they don't want to turn. so, do you need to grind for them to turn generally, or is every single one different? I got the driver side in, but now i am having trouble getting it to come back out. it comes part way, but then won't go anymore, i can wiggle it up and down, but it just freakin wont come out!
anyone have before and after pics of how much they had to grind? i've searched and read all the disk brake swap sites, but no pics or anything about how much to grind, or anything.:censor:
 
Thanks Poser! I yanked and moved it and it came out. looks like i gotta grind on the bottom some more. I'll try to post some pictures tomorrow.
 
Clearance for Birfields

I don't know for sure how much you have to grind for the birfs to slide in/out freely. My recollection is about 0.050". I do remember that I thought everything was cool (enough clearance), and I put my knuckles on, and torqued down on the knuckle bearing caps. After doing this.......birfs would not slide in/out. Loosen the knuckle bearing caps, and the birfs are free.
 
atazman said:
I don't know for sure how much you have to grind for the birfs to slide in/out freely. My recollection is about 0.050". I do remember that I thought everything was cool (enough clearance), and I put my knuckles on, and torqued down on the knuckle bearing caps. After doing this.......birfs would not slide in/out. Loosen the knuckle bearing caps, and the birfs are free.


.050" ? How do you measure that and what are you using to remove the material? A typical abrasive disc on a 4.5" grinder will remove .050" in about two seconds....




You need to grind the opening more, as you should not need to loosen the knuckle to remove an axle....you do not need to on a factory disc axle.



:beer:
 
Keep on Grinding

Well....., Poser, you got me looking through my archives. But I did not find all the details of how much I ground. Distance across flats on the longfields was 3.393"; distance across flats on my '76 Birfs was 3.320". To keep the same clearance, a comparison of these two measurements suggests that I would have to grind out 0.073". However, my intent was to grind only enough for the new Longfields to fit. And how much I ground is still a mystery.

When I realized that torquing the knuckle bearings down actually closed up my gap, I continued to grind, assemble the knuckle, torque down, and test to see if Longfields could be slipped in. After several gyrations......I finally got the clearance I need so that I don't have to loosen the knuckle bearings to get the longs out.

So....I would say that I actually ground out less than 0.073", and I did it very slowly with a 4 1/2 grinder.

Thanks for your comments.
 
atazman said:
Well....., Poser, you got me looking through my archives....
I'm supposed to have maintenance technical archives? :eek:


I guess I need to refine my obsession. :grinpimp:
 
NO actual pictures yet, but i ground the drivers side more, and almost have it. had to take quite a bit more out. definately checking how they turn in there before i start bolting greased parts together again! pics friday maybe. (hard to find time to work on it during the week).
 
All this talk about knuckles and gyrations is making me laugh. I didn't measure mine, one because how would you measure it? and B why would you measure it? who cares grind it till it works, you could have had it done by the time you turned on the computer. Just kidding. Tom
 
Back
Top Bottom