Interval of repacking bearings

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 19, 2007
Threads
18
Messages
36
Location
STerling VA
Can someone tell me what the appropriate interval would be to repack the front bearing on the 80. I have put about 20K miles since the last time i had the bearing repacked. Any / all help would be great. Given my LC has 152K on the clock i do not know if or when the wheel bearings were changed. Is it time to change them or should i not touch them unless they go Bad. Also anyone from Northern VA here if you can recommend me a good shop that would be great. Last time i went to Tysons Toyota they told me it was time to trash the truck.
1994 LC 80 Yes Front Bearings.
 
I think it's in the factory service manual for 30,000 miles?? Anyone got one handy? By the way, I'm assuming your truck's year and I'm assuming you are talking front WHEEL bearings so correct me if I'm wrong.

DougM
 
30k on repacking the wheel bearings (inner & outer, front & rear). Toyota doesn't give a service life on those bearings and they are very large and well made (Koyos are preferred by some over the Timkens)

If you routinely repack the wheel bearings every 30k and don't sling them across the garage and bounce them off the concrete then they should last 300k or more. Of course, you should inspect them at each repack.

This is not true of the trunion (aka knuckle) bearings. They are much smaller and support the full weight of the truck. They "live" in basically 1 position (straight-on) and take a lot of abuse from pot-holes and mall curbs. Most recommend that you replace the trunion bearings at each 60k mile front axle service. I know you didn't ask, but it was on my mind and when something is on my mind, it is on my lips ... err fingertips.

-B-
 
Stupid questions what are Trunion (knuckle) bearings. The most i have done on my own on this truck are brake pads and a starter motor. I was not there when the bearings were last done. So an explanation of trunion bearings would be great. Thanks i am learning is all that matters right.
 
So, I guess the hint on the year of your vehicle was unheeded. Um, Year? Country? Engine? Transmission?

DougM
 
Posted a pick of the FSM showing the 2 trunion bearings, one on the top one on the bottom. Hope this helps
bearings.webp
 
Idaho Doug,
Its a 1994, 1FZ motor 4.5 L 24V, Country Sterling Virginia USA, Transmission (Bus Tranny is what the dealer who did the repairs told me A.. Hole) Color Dark Green, Seats cloth interior, No Lockers, 151K, new Exhaust and Its my daily driver. Tooth DR thanks for the the picture, i think this will be a job i take in to get done as i am a tat bit scared of opening up so Much. Anyone on here from Northern VA and can recommend a good shop to get the work done at. My old man has 2 1hZ turbo diesels (GXL and VXL) back home in Africa with the 5 speed trannys. I love hammering on those when i go visit such a lovely noise those diesels make.
 
Also, don't forget the rear wheel bearings, they require inspection and packing as well. Use only Koyo or Timken bearing; some bearings are made in Mexico and are not to cruiser spec.

...
 
(Bus Tranny is what the dealer who did the repairs told me A.. Hole)

The shop doing the repairs was correct. The auto tranny used in the early years is a primitive transmission designed for (and more suited to) use in a small bus for the JDM.

Color Dark Green
I am SOOOO sorry. Sometimes you just have to take whatever crappy color is left. Seems most buyers avoid 6M1 like the plague so those are the only ones left for the less discriminating shoppers.

-B-
 
Back
Top Bottom