Internal Winch Control

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 5, 2006
Threads
404
Messages
1,234
I have seen a few references to using a 4 runner rear widow control switch as an internal winch in/out controller, but I cannot seem to run a search of the archives to pull up a specific how-to "build report".

I can run a search that pulls up several references relating to switch relabeling, but nothing outlining how to wire up the modification.

Can somebody point me to a thread ?

Is the Slee circuit board only necessary because the land cruiser antenna up/down can be pressed simultaneously, and a auxiliary circuit board is not necessary for the 4 runner window because it is a momentary 3-way switch, with up/down as mutually exclusive options ?

What 4 Runner model years provide a ready “drop in” dimensions for the switch openings the 95-97 Land Cruiser dash?
 
I have nothing to add for help other than..... glad to see ya working on the 80;)

Oh yea, I bought the slee board & still have to install it...... wifes in school:rolleyes:
 
It actually is not that hard to wire using two contura swithces and they just happen to fit in the coin slots in the 80

Cam
 
...Is the Slee circuit board only necessary because the land cruiser antenna up/down can be pressed simultaneously, and a auxiliary circuit board is not necessary for the 4 runner window because it is a momentary 3-way switch, with up/down as mutually exclusive options ?

Yes, pretty much that's it, at least for Warn winches. Not sure about other brands. Even with Warn, the hand control that comes with the winch switches both the +12v lead and ground. I.e. when you press the "in" or "out" button on the control, +12v is switched to one pair of control solenoids or the other (depending on desired rotation direction of the motor) AND the common return side of the solenoids is switched to ground. I'm sure this redundancy is done as a safety measure, so that it takes more than just a short in a wire or a fault in a switch to make the motor run. If you want to retain this level of redundancy, then you'd want to add an arming switch that when "on" switched +12v to the common terminal of the 3-way 4Runner switch AND switched the common solenoid grounding lead to ground. This would require a DPST arming switch or a SPST arming switch and a SPST relay. If you want to forgo the extra safety, then just connect the common solenoid return lead to ground permanently.


What 4 Runner model years provide a ready “drop in” dimensions for the switch openings the 95-97 Land Cruiser dash?

I don't know the model year(s), but the Toyota part number you want is 84810-89103.
 
What 4 Runner model years provide a ready “drop in” dimensions for the switch openings the 95-97 Land Cruiser dash?

Camry's and Corolla's have many switches that will work. I've found Cruise, Hazard, Defrost, and other switches that fit perfect.

I'm using the defrost button for my Hella lights, I've seen the hazard used for CDL, and I have a door lock switch that is a spring loaded rocker switch (like our rear heat switch, but only momentary, goes back to center after depressed) I think it would work great for a winch control and plan to use when I get a winch...unfortunately it is not lighted but I'm sure there are some out there.
 
Hey CLUTCHEE !!!! Good to hear that you are staying out of trouble ! It makes me smile everytime think you southern folks waking up to fresh snow in July during ACT 2008!

yup working on the '80. Seems like I have a bunch of things started & nothing finished !
winch mounted, not wired in.
4x4 labs bumber installed, but exhaust still swinging
weather strippping on rear amby doors on the FJ40 3/4th's glued in,

I have GOT to focus and get things finished.
 
Back
Top Bottom