Intermittent brake light problem. Any ideas?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 11, 2005
Threads
126
Messages
3,326
Location
Alabama
I bought this truck in November. Every so often, I can't shift out of park and have to override it. I checked, and sure enough, the brake lights didn't work when this happens. I figured it was the trailer harness which is a huge rat's nest piece of crap. So I pulled all of that yesterday and fixed up the wires that they spliced into. The brake lights still don't work. I'm guessing that there is a bare wire bouncing around somewhere. It is both brake lights that aren't working. The bulbs are fine.

Any experience with this or a direction you could point me in? I'll get the voltmeter out after work today and start checking stuff.

I h8electrical problems.
 
might be worth checking upper left of upper hatch - bundle of wires pass through here (including third brake light if you have one) mayneed to carefullt peel back headliner at that corner for access (use gloves and do it in warm weather if possible) I had a wonky third brake light and rear wiper that I have finally seem to have cured - (knocking wood) good luck!
 
I don't think mine has the third brake light. Regardless, I doubt that would cause the other two lights to go out.

my '94 has the 3rd brake light.....You could be right though....I don't recall having trouble with the two lower brake lights when my 3rd brake light was wonky.....
 
I don't think mine has the third brake light. Regardless, I doubt that would cause the other two lights to go out.

What do you mean you don't have the third brake light? You should. It came standard with your model.

The towing harness was a complete dud. That f'ed my old Cruiser up as well. I would check everywhere the loom is fed through a tube; you could have chafing there. If you pull the interior panels, get some more retainer clips and replace the old ones; it helps with rattles.
 
What do you mean you don't have the third brake light? You should. It came standard with your model.

The towing harness was a complete dud. That f'ed my old Cruiser up as well. I would check everywhere the loom is fed through a tube; you could have chafing there. If you pull the interior panels, get some more retainer clips and replace the old ones; it helps with rattles.

Yeah, I pulled the panels last night when I pulled the trailer harness. They are still sitting in the back. I only broke about 4 clips but I need to buy some new ones anyway. I've run my hand through and around every hole that I could to see if any of the wires were chaffed, but I found none. This afternoon I'm going to search toward the front of the vehicle...

Maybe it does have the brake light. I'll check at lunch. I never paid that much attention to the upper lift gate.
 
Yeah, I pulled the panels last night when I pulled the trailer harness. They are still sitting in the back. I only broke about 4 clips but I need to buy some new ones anyway. I've run my hand through and around every hole that I could to see if any of the wires were chaffed, but I found none. This afternoon I'm going to search toward the front of the vehicle...

Maybe it does have the brake light. I'll check at lunch. I never paid that much attention to the upper lift gate.

I'm confident it does. Good luck.
 
Fixed. It's always the simplest s*** when it comes to wiring problems for me. After I checked and had zero power to brake light wire in the rear area, I pulled the front under the dash apart. This gave me the opportunity to pull all the bull**** from the add on alarm and keyless entry. I liked the keyless, but I hated the alarm going off all the time. So it had to go.

Alright. So I pulled the brake light switch from the pedal and checked the resistance with my ohm meter. It was good to go. So I checked the harness that plugs into the switch. It had some weird voltage. 3 volts, then 7 volts, then 2, etc. I used a jumper wire from the fuse block to the harness and the brake lights work. So I knew the problem was between the fuse block and the bl switch. I pulled the fuse block and measure the voltage. I had 12V to the incoming side of the fuse. On the outgoing side of the fuse I had only 8 or 9 volts. Weird. Measured some others and they had 12V. It turns out that the slot that the fuse slides into was bent out a little bit so that the fuse wasn't making good solid contact. I squeezed it down and now all is well.

So now at least I have cleaned up some of the wiring. I need to find a good trailer harness now. Does anyone know what those unused harness connectors in the rear quarters are for?
 
Back
Top Bottom