How level?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 9, 2006
Threads
101
Messages
513
Location
Alpharetta GA
Probably been discussed a million.5 times. Ordering my lift and bumper, tires, gears etc today or tomorrow. Still torn between the heavy fronts or the j fronts. Decided to stick with the medium rears regardless. No 3rd row, no rear tire carrier for at least a year and will probably remove the hitch also. I am installing an ARB front bumper with no winch for at least another couple of months and sliders will be hopefully sometime in September/November. I'm going to run the Slee caster bushings or maybe Landtank's. Not sure yet. Anyway just wondering how close to level I will sit with the heavy's up front and or the J's. I didn't want to get into lowering the front sway bar and longer brake lines and d-shaft problems if I'm going to be looking at that with the J's. Tell me what ya think:cheers: P.S. Going to run 315 terra grapplers with only probably 2-4 times a year wheeling.
 
860 front, with 850 rear is a popular setup. With only a ARB up front, you may sit a little more level on an 860 set of springs. Check with Slee, but ARB only loaded J's up front may negatively effect handling with mediums in back. Picking springs based on load front and rear is key.

There are some minimum modifications that should be made if you're planning on J's which you've named. I'm not sure if I've seen anyone with J's up front and medium rears. 860 fronts with a spacer are common and should satisfy your needs for now. If you want to switch to J's all around in the future, used OME springs sell rather well. If you really want J fronts, look in the for sale section, there is a brand new set for sale.

With the 315's on stock rims, you should only have to extend your rear bump stops 2" to prevent rubbing.
 
Here is my 96 with J's in the front and heavies in the rear. I have a spare tire and no third row and a full tank of gas. Front has ARB and a Warn M8000, and an 80lb battery. I am putting in the Slee 1" spacers up front this weekend and hope to get a bit more level. From ground to top flare in front measures 38" and rear 39".
IMG_8157.webp
 
Here is a pic before the winch, new battery and sliders. Even with the J's it still sits a little lower in the front.
IMG_7145.webp
 
Last edited:
hey, Tommy, I have the Heavies up front and I just lowered my sway bar, anyway. I, too, have an ARB, no winch, and sliders, no rear bumper. When I was replacing the u-joints in my front driveshaft, I noticed that the slipjoint dust cover was dented from contacting the sway bar at some point so I put in the Slee drop blocks. Cheap and easy insurance. Was about a 15 minute install.

Might make a difference with a winch and, say a dual battery setup up front with the Heavies, but without, you may be looking at sway bar drops and brake lines anyway. I'm looking at brake lines at some point.
 
Here is a pic of mine. I have j's up front and mediums in the rear. Up front i have a bull bar with a 12,000 lb winch with steel cable. I have no weight in the rear at all. I sit stink bug and i'm seriously considering going 4 inch springs up front.

EDIT: crap, actually now that i think back, this pic is WITHOUT the front winch. So it squats a little more than pictured with the winch
Nitto 315 002 (Small).webp
Nitto 315 003 (Small).webp
Nitto 315 004 (Small).webp
 
Here is a pic of mine. I have j's up front and mediums in the rear. Up front i have a bull bar with a 12,000 lb winch with steel cable. I have no weight in the rear at all. I sit stink bug and i'm seriously considering going 4 inch springs up front.

EDIT: crap, actually now that i think back, this pic is WITHOUT the front winch. So it squats a little more than pictured with the winch

Perfect! Thanks for all the responses. I am going crazy waiting to weld the credit card. I also get the joy of resealing the front end:idea:.
 
tommy--

moonglow above is mine w/ 4'' front and j's rear (better pic below). Id agree w/ midlifer; get the j's and youll still be a hair low up front.

Did you ever find some sequoia rims?
wheel change 002 (Medium).webp
 
J, isn't that pic with the J's up front? It looks pretty stinkbug and i know it sits MUCH more level with the 4's up front now.
 
ok, here are some pics i just took. The first three of are JFZ80's :princess: rig. It has slee 4inch coils in the front and j's in the back. No weight at all. I think it sits nice and level. Funny thing is that i have driven this rig, it rides great with the 315's, but when he runs the 295's that are on it in this pic, it wanders a lot more. He is only running OME CC bushings. No real grrrrrr.... you can feel the faintest grrrrr.
starterandstance 008 (Small).webp
starterandstance 009 (Small).webp
starterandstance 010 (Small).webp
 
now here is my rig. I have j's up front and mediums in the rear. No weight in the rear. Winch, bull bar, steel cable on my winch. I have a bad grrrrr with a stock shaft, and a really bad buzz with a DC shaft. I'm running slee's plates wit stock bushings. I'm about to take the plates out and put slee's 3 degree bushings in.
starterandstance 012 (Small).webp
starterandstance 011 (Small).webp
starterandstance 013 (Small).webp
 
Here is my 96 with J's in the front and heavies in the rear. I have a spare tire and no third row and a full tank of gas. Front has ARB and a Warn M8000, and an 80lb battery. I am putting in the Slee 1" spacers up front this weekend and hope to get a bit more level. From ground to top flare in front measures 38" and rear 39".

i just did this the other day. i got tired of the stinkbug look. i almost have the same exact set up as you do aside from the sliders and arb bumper(no sliders and slee shortbus). i just installed the 1" front spacers and and all is somewhat level. i got a reading of 39.25 in the front and 39 in the rear. the front was 38 and some change prior to installing the spacers.

cheers.
 
i just did this the other day. i got tired of the stinkbug look. i almost have the same exact set up as you do aside from the sliders and arb bumper(no sliders and slee shortbus). i just installed the 1" front spacers and and all is somewhat level. i got a reading of 39.25 in the front and 39 in the rear. the front was 38 and some change prior to installing the spacers.

cheers.

Awesome! Decided on sticking with the J's up front. Thanks everybody!! I am about to get severly in debt. Next up............., www.sleeoffroad.com. :D
 
i just did this the other day. i got tired of the stinkbug look. i almost have the same exact set up as you do aside from the sliders and arb bumper(no sliders and slee shortbus). i just installed the 1" front spacers and and all is somewhat level. i got a reading of 39.25 in the front and 39 in the rear. the front was 38 and some change prior to installing the spacers.

cheers.

The stinkbug effect comes because the springs you installed are pretty much even height. If all four springs are even, the rear of the 80 comes out about 2" higher. To avoid the look, buy springs with the front pair an inch higher than the rear pair. Either that, or put 1" spring spacers on the front.

I think you need a bit of stinkbug for loads, but an inch is good enough for me as it's pretty much invisible to most eyes.


Kalawang
 
tommy--

moonglow above is mine w/ 4'' front and j's rear (better pic below). Id agree w/ midlifer; get the j's and youll still be a hair low up front.

Did you ever find some sequoia rims?

What brand of sliders are on this rig?
 
This rig

This rig that is...looks just like mine...minus the sliders...:flipoff2:
starterandstance%20010%20%28Small%29.webp
 
Back
Top Bottom