Hot Tranny in 94 UPDATE

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 20, 2004
Threads
104
Messages
1,929
Location
A balanced city
Ok so after thinking long and hard about this I decided I would start with the cooler....pulled both lines no fluid in either line and very little in the cooler..blew it out with compressed air,

Disconnected both lines from the tranny and blew both out with compressed air. Got a fair amout of fluid from the front line, the one with the sender attached and very little from the other.

Reconnected everything back together and started truck, checke dteh fluid and went for a drive....truck drives and shifts nice, no warning lights on dash.

According to gauge the fluid was at 180 and confirmed this with a infared thermometer i bought the other day. But the facttaht the cooler was cold to the touch and when I disconnected the upper line into the cooler there was no fluid bothers me...

So should the cooler have fluid??? Any ideas as to why the tranny is not pushing the fluid to and from the cooler??

Any help would be great cause I sure cant afford to blow up this tranny...Thanks guys
 
I'm no tranny expert, but IIRC if the tranny shifts, the fluid has to be going through the cooler. If it weren't going through the cooler it wouldn't be circulating at all, which means the tranny wouldn't shift or probably even move. I don't know for sure, but I don't think there's any way for the fluid to bypass the cooler.

-Spike
 
Thnat was kinad what i was thinking and when I blew the air through eveything proved all was clear...just wondering why the cooler was cold to the touch when the radiator was hot....made me go mmmmmm
 
Fkuid level looked good but will recheck when its cold and I can find a flat spot to do it...thanks
 
The truck was running and the fluid level looks ok...maybe a little high...that make a difference???

Does anyones cooler get hot after driving??
 
Are you sure the tranny is hot? By what standard? If you explained this before, link to it.

-Spike
 
If your cooler isn't getting hot, something is wrong.

I'm leaning toward clogged cooler or lines.

Have you tried to take off cooler and run fluid through it?

Maybe connecting the lines together (bypassing the cooler)
to make sure it's getting out of the tranny.

Lines + cooler should be warm or hot depending on fluid temp.
 
That is whta I was thimking...cooler should be getting hot...blew out the cooler and both lines with compressed air today...all seemed clear..should the cooler lines have fluid in them when I start the truck and shift from park to drive?? I had my daughter shift the truck while it was parked and nothing came out??? Just trying to figure this whole auto tranny thing out...need to order a FSM soon..Thanks guys
 
I dont know what tranny it is sorry new to the 80 world....also do auto trannys work in a closed system like a radiator??? maybe an air bubble??
 
I dont know what tranny it is sorry new to the 80 world....also do auto trannys work in a closed system like a radiator??? maybe an air bubble??

I don't think an air bubble is likely, it's not like a brake system in that respect.

Do you have the owners manual? It would probably tell you what tranny it is but I think it is a A442F. I found something about checking fluid between a certain temp. but I don't know if it applies to your trans.
I would look in the owners manual and see what it says if anything about it. (assuming you have it) :D

Didn't find anything decent from the 100 series manual, sorry.

If it is pushing enough fluid to move the vehicle, I would think it should be pushing the fluid up to the cooler and back through.
 
Thanks for all your help. I will check the manual in the morning and find out what tranny I have....I agree the tranny pushes fluid thru the cooler and the truck shifts and drives fine but cooler never gets warm. Just wondering if anyones does?
 
The fluid does not pass exclusively through the tranny cooler and back, it's routed through the cooler via hydraulic passages in the VB/tranny body and back.

The Torque Converter does not supply the needed pressure to the tranny, only the oil pump. The pump supplies fluid pressure to all components, TC, VB, clutches and brakes.

One Adam 12,

Did you take the cooler unions off the tranny or just the line from the union? You may have a clog in the union.
 
I took the lines out of the unions...guess I need to take the unions off now..

Can anyone confirm the fluid needs to go through eberything inorder for the tranny to run right??? ie through one of the cooler lines then through the cooler and then back to the pan...cause as of right now all lines check clear except the unions..

I just checked the fluid level at start up...seemed right about where it needed to be...
 
Back
Top Bottom