Holset Turbo To 2F

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

LC_Hamma

The Anti-Leafer
Joined
Nov 11, 2002
Threads
98
Messages
2,656
Location
Dallas, Georgia
Thinkin' about the Turbo 2F thread & lookin' at my Cummins 6BT got me dreamin' about mating these two together. It's a Holset & could mount similar on a 2F as what's shown here. I could pick up a used Cummins exhaust manifold & cut off the turbo mounting flange, then tig it to the 2F manifold. Is this turbo similar sized to the Garrett T03/04? The routing of the oil lines doesn't look very complicated. Would I need an aftercooler for it? I'm gonna run fuel injection too, if that matters.
 
Last edited:
haha, one of my buds co-ops for holset...been tryin to figure out how to use that hook-up to benefit the cruiser


malphrus
 
Most of the turbo's that are designed for a Diesel are huge for a 2f. However, There is one designed for a 4 liter Diesel that will probably be perfect. If you have some sort of wastgate that will limit the amount of boost you are seeign you will be fine.

Turbo's and 2F's work very well together...
 
What size exhaust housing is that?

It says 185 cm. on the housing. Type H1C. It's 2" I.D. on the exhaust opng.
It's a factory turbo, & from what I've read about these, they're an HX35.

However, There is one designed for a 4 liter Diesel that will probably be perfect

Okay, so the turbo for the 4BT will be the one I need (?)
 
The newer cummins 5.9's use a 9cm housing(that one must be 18.5cm) you could try that it might work well. I am running a 16 cm on my 3B and it works great it is a little bit slow to spool so I am going to try the 9cm myself.
 
A cummins 6 turbo will be way too much..
 
The 4 and 6 turbos are the same (H1C) the work load on the 4s were high so they ran a low boost. the turbo I think you could use would be the HY35(smaller exhuast housing), its the turbo off of the automatic tran. dodge 6bts either that or by an hx35 and get a smaller exhuast housing(quicker spool). or you could go with the hx35-40 hybrid, 35 exhaust 40 intake, that should push enough air for you or you could just run a nice set of twins.
 
IMHO, you'd be a lot better off with a wastegated Garrett T3 from a Saab/Volvo/TBird Turbo Coupe, etc. Find one with a compressor A/R of .42 and and exhaust A/R of .48...those with .63 exhaust A/R might not spool quick enough. you will want to adjust the wastegate actuator to pop off at 5-7 psi. Google is your friend here...I think the Cummins turbo would be way too big, and never spool. my $0.02, not gospel.

Steve
 
The cummins Turbo the HY35 mentioned earlier was only on the 01 to 04 automatic tranny dodges because it spools very very rapidly it would probably work very well on that motor due to the fact that when ran on the cummins engine it reached full 20psi of boost very very quickly, and so reaching even 11psi would be rather acheivable on a smaller engine. Just my comments.
 
could be...you never see maps on the Holset stuff like you can find anywhere for the Garretts. hard for me to believe that a turbo that works on a 5.9 liter diesel will spool on a 4.2 liter gas motor, but the 9cm2 turbine housing might let it work. never had them both in my hands, either.

Steve
 
Found this thread doing a search on google for my 4BT :) A little late but I have been doing some research. Sherpa is exactly right. If it's an H1C then it's non wate gated. Off a 6BT probably has a huge housing like a 18.5 cm2 or something like that. They make them all the way down to 9 cm2.. 16, 14, 12, then 9, so you can really tweak them. Housings are about $150 each new, cheaper used but hard to find in the smaller sizes. If oyu are using one of these, they are way easy to plumb and like everything on a Cummins way easy to setup, take apart, etc etc... This would be a good option, I like Diesel Dude's logic of thinking. The advantage of the Holset is once you set it up, if you don't like how it spools then you can change it. Versus a smaller gasser, what you have is what you get unles you want to get into expensive turbo mods and keep the same housing.. Also a diesel seems to put out a lot more air per volume, especially a turbo so it might spin up the turbo faster than a gasser, I dunno... Compression ratio is something like 17:1 per similar volume (say a 3.9 liter cummins like mine) vs a 4.2 gas engine at 8:1. So that means the gasser might have trouble spinning the turbo as well because this locic leads me to believe more than twice the air per the same abount of volume... ??? Andre
 
Also you can interchange the wastegated and non wastegated housings between all turbos. A bigger turbo like a WH1C, HY35 or HX35 off a later 6BT might be the ticket versusd a smaller one with a smaller fan like the H1C. All these are wastegated versus the H1C which is not waste gated. I only know this because I'm in the middle of trying to put a WH1C with a 12cm2 wastegated housing onto the 4BT, but will probably end up with a non wastegated 12cm housing because the wastegate actuators hits the block on the 4BT... Or I have been told to simply weld the wastegate closed. Which I have been considering as well... Steve, I finally subscribed to TDR today, after years of dragging my ass... :rolleyes:
 
h1c 93 and earlier dodge 6bt, early 94 i hear as well. 21 or 18.5cm housings. used on most 4bt in all applications, but can come with the smaller housings

less effecient then the 94 later hx35, 12 n, 14 n, 16 n, 12 g, 14 g, 16 g

biggest changes are the blades themselves.

Think is going to be too big as well.

how about a 7mgte turbo?


i do have a 2f, h1c, and hx35 in my hands :)
 
ok now what does it take other then redoing to exhaust and the intake?
 
Back
Top Bottom