HELP: Crank, no start!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I hope he gets it started but since he didn't have an hour to run a compression test and report back, I'm thinking it's a hit and run. I sincerely hope not but it's frustrating to see all the suggestions you guys gave and not see any action on the OP's part.
 
I hope he gets it started but since he didn't have an hour to run a compression test and report back, I'm thinking it's a hit and run. I sincerely hope not but it's frustrating to see all the suggestions you guys gave and not see any action on the OP's part.



Thanks for the vote of confidence! Easier said than done during the holidays in the winter to get out there and work on it, the vehicle is not in a garage.

.........
 
OKAY! MOVING ON!

I'm back on the case.

A) I found that the dealership was full of crap. The plug wire for cylinder 4 lost its rubber grommet (still stuck on over the plug ceramic) which moisture seals the plug, so they definitely did not test cylinder 4. Although they povided 100 psi for that cylider (were they guestimating?).

B) After going back and trying to restart and actually getting a real timing light, I've discovered that I'm not getting ANY spark from the primary coil-to-distibutor wire.

* I've manually tested the coil's resistance to be approx. .40 Ohms, and further jumpered the coil to the battery directly and fired it manually by intermittently applying power and the timing light fired up to confirm it is working.

* I've confirmed continuity of both wires between the ignitor and the coil as well as the two wires (IGF and IGT) between the ECM and the igniter pins 17(ECM)->1(ignitor) and pin 23 (ECM)->2(ignitor).

So I've isolated the problem to be one of two things:

1) No signal from ECM to Ignitor
2) Ignitor is bad

I've checked the Haynes manual, but there is no information about the type of signal between the ECM and Ignitor. In fact they have specs and troubleshooting for the coil as well as the distributor 4-wire harness, but not for the ignitor. Dunno if its a 12V high-frequency signal or less. I don't even know if which (IGT or IGF) to test and how to do it.

Does anyone have experience with trouble-shooting the ignitor signal from the ECM?

(In the mean-time I'll scour the forums for this answer)

THANKS!
-f4t
 
Last edited:
Good troubleshooting!

I am on the road for a few more days. I don't have easy access to the FSM but if nobody can post those sections for you then I will do it when I get back to civilization.

-B-
 
Check the fuseable links and make sure they are good.
 
I have the wiring diagrams (harness locations and connector descriptions) from the Toyota Service Manual in PDF. It helped me tremendously in troubleshooting up until this point.

The only thing it doesn't describe (unless I missed it) are the specs (tolerances, etc..) for the IGT and IGF connections.

A good suggestion infojunkie on the FLs. I had already checked them before, but I will go back and do it again tomorrow.


In the meantime if anyone has the info for the voltages and other characteristics, I appreciate it.

Thanks again.
 
i know its simple, but make sure you didn't tear one of the three fusible links that come off the positive battery terminal...

i did it accidentally and wanted to kick myself a week...
 
Got you message F4T, I don't know if I can provide much help from here. I can tell you that the Haynes Manual is a bit of a POS when it comes to detailed diagnosis of an electrical gremlin. But frankly I don't find the FSM to be a silver bullet either.

I'm sure someone will chime in with some help though!

How about those robbers at the dealership. Shameful, and embarrassing. I hope once it's fixed you go back and get a refund for their "diagnosis" of it needing a "new engine". Or even better take them to court!
 
Got you message F4T, I don't know if I can provide much help from here. I can tell you that the Haynes Manual is a bit of a POS when it comes to detailed diagnosis of an electrical gremlin. But frankly I don't find the FSM to be a silver bullet either.

I'm sure someone will chime in with some help though!

How about those robbers at the dealership. Shameful, and embarrassing. I hope once it's fixed you go back and get a refund for their "diagnosis" of it needing a "new engine". Or even better take them to court!


I'LL TELL YOU WHAT.. I'm pretty darn close to taking some kind of action. But I now need to prove them wrong first!

I didn't get a chance to play with the truck today, so I'll try again tomorrow.

Thanks for the words sbfj60fig.
 
I've check as much as I could on connections but all seem okay. Is there a sticky round here that shows *where* all the fusible links are? I'd like to go through each/all of them. The diagrams are a little sketchy with the locations.

I need to find out WHY the ECM does not send a signal to the ignitor or validate the ignitor itself isn't bad, but I don't see anywhere a way to test the ignitor!

My only hope is there's a burnt link or bad ignitor!



Thanks.
 
At this point I'm going to assumer the igniter is the problem. Haynes' troubleshooting section states that if the igniter sees 12v power at the terminal (which it does) then replace.

I see one here used, dunno what they cost new, but I'm calling Toy in the morning. Fingers are crossed.

-f4t
 
Did you check the pickup coil in the distributor?

I just bought a non-running 91 so I'm going through pretty much the same thing.
 
Yeah thanks for the suggestion.

The coil tests good with a manual test direct to the battery.

I also tested the contacts of the harness on the distributor. The specs say these contacts should provide 240~325 Ohms cold, and although I measured around 205~220 I believe they should still operate enough for the truck to run (Ill get to that later if I can find a spark).
 
Keep going...you'll get it!
 
How about a malfunctioning alarm system, factory or aftermarket?

I have a Prestige (audiovox) aftermarket alarm with remote start. It was installed by a car boutique in NJ. I have the installation diagrams and do not see where it cuts-off the coil, igniter, ignition, etc it only disables the starter relay.

NOTE THE FOLLOWING:

* The alarm has never failed and still works today.
* I've set the alarm off and confirmed that its M.O. is to disable the starter relay (not the coil)
* I've also tried the remote starter functions and it cranks the 1FZ-FE, but same issue (no spark).


I believe at this point I can rule it out. I did check all of its connections and fuses and all are okay. I've even bypassed/disarmed the alarm and no difference.


UPDATE: I called Toy and found the damn igniter to be ridiculously priced. I'll have to see if I can find a used one or aftermarket.

I still have NO IDEA as to how to test the igniter itself. ANY IDEAS?
 
UPDATE: I called Toy and found the damn igniter to be ridiculously priced. I'll have to see if I can find a used one or aftermarket.

How much $$$ was it from satan??
I might be looking at the same problem.:doh:
 
DAMN.

It's not the igniter. Replaced it today and tested, but still no spark. Gonna do more testing.

TrickyToy,
The igniter is $400 from Toy.

Ouch, that hurts... Don't give up, man. I will get it. Victory belongs to the last standing...
 
FYI igniter is used on other toyotas....I picked up a spare from pick and pull yard...

IH8MUD Forums - View Single Post - connected battery backwards and smoke

If you look at the pic in the link, you will see a small black box in back of the battery tray, this is where two of the fusable links terminate, the third terminates at the grey connector shown just below it. check with meter and see if one is blown.
 
Back
Top Bottom