Head Gasket OOPS!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 18, 2002
Threads
101
Messages
1,210
Location
Rosamond Ca.
So, I get the top end of my 1996 FZJ all torn down, and it hits me! FAWK! I forgot to bring the engine to TDC before I took everything apart! Don't ask, I'll fess up. NO I did not mark either of the cam gears either.

WTF was going through my head as I took this apart? Strangely enough I marked and organized every bolt that came off this thing. I just forgot to....see above...

So, that being said, YES I know... DUMB-ASS!!!!. Laugh, Point, snicker, point and laugh some more. Do I need to tear the front end down to make sure the timing chain is where it should be in relation to the crank?
 
oh S--T!!!! bet you feel quite sick, I know I would, I have not done my HG yet and at 165k I bet it will be quite soon :-(

I would guess you will have to keep the timing chain tight on the crank sprocket, as you slowly turn the crank clockwise until the crank pulley timing mark aligns up and making sure the rotor arm is pointing to No1 spark plug lead.

I would not try that just yet, wait until you hear from other really helpfull guys on here, they may have a far better way of sorting it out.

Good luck and I will keep watch to see how you get over the issue, its the sort of thing I would do :-)
 
Just hold the cam gear so there is tension on the chain, then turn the crank with a ratchet. There are markings on the cam gear that should line up with markings on a chain link. It will be obvious it's correct when the markings line up and pistion number one is at the top. READ THE FSM about the correct marks to line up since I'm just going off the top of my head.
 
Before you do anything else, a little more info.

Is the head off now?

Can you get a pic of the block from the top so we can see how the pistons are?

Also a pic of the timing chain.

I just finished my HG and forgot where I was when I was cleaning my pistons.

It can be fixed, just don't panic.

There are some smart folks here who can help.

Good luck.
 
Yup, the head is off and #1 is about 7/8" from TDC.

Hopefully I can put a little tension on the timing chain, and turn the crank a bit. My big concern, is has it dropped off the crank a tooth or so? Is there something in there to keep that from happening once the cam and cam gear, and tensioner are removed?
 
No problem here whatsoever. When you reassemble you'll be mechanically putting the engine in proper time anyhow. Before putting the head on, turn the engine in the direction it operates when running such that the front piston (#1) is at the top of the cylinder, then look down at the pulley and mark on the front of the engine to put it exactly at 0. Nice to have a helper keep tension on the timing chain during this. Now the #1 cylinder is at TDC. Then, when you use the marks on the camshafts to properly align them for assembly per the FSM the engine's top end and bottom end will be properly timed to each other. Now the pistons and valves are properly timed.

After this when you install the timing gear/timing chain (watch that you use the correct alignment bolt) there is no chance of a link being "loose" - there is not enough chain for that kind of slack. You would not be able to get it on if a chain link were kinked/loose. When you subsequently install the distributor (watch the helical gears will tend to rotate it a tooth as it slips home), it will match up the ignition timing to the rest of the engine you've already correctly timed mechanically. The word "timed" here is used when rotating parts are mechanically timed in case I've confused anyone.

I assume you have a FSM.

DougM
 
Thanks Doug

No FSM yet, I was using the Haynes for tear down. Yes.... I know the FSM is vastly superior to the Haynes. I will be looking for a FSM before I put everything back together though.

Thanks for the description of the reassembly, it helped clear things up. Actually it reminded me, that the chain itself is not the most important piece of this puzzle. It doesn't matter where it's positioned, it's just a set of evenly spaced links (for some reason I was concerned with it dropping off the crank sprocket as it sits now, and needing to be put back into a "set" position). What is important though is the position of the cams in relation to the cylinder/crank position. Hence the dots to be lined up correctly (when re-assembeling it all), when the engine is at TDC. I don't know why I freaked out when I realized my mistake. I have rebuilt engines before, from square one. This is my first time tearing into a DOHC engine though. Now I REALLY want to get an FSM and compare it to the Haynes on re-installation. I am sure the Haynes will get me in the ballpark, but the FSM will refine that procedure quite a bit more.
 
Back
Top Bottom