Getting dizzy. Upgrade to electronic ignition?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 10, 2004
Threads
175
Messages
948
Location
coastal empire
I have a '68 F 145 that is running like krap. After a little investigating, I found that I'm not getting spark to all of my cylinders. Prior to the problem, I have replaced the rotor, cap, wires and plugs so these are new (less than 1000 miles on these).

I noticed that when I manulipate the dizzy cap by grabbing on it and "moving" it around a little, I'll get a spark to a cylinder but then it'll cease when I take my hand off.

I'd love to fix what I've got and stay stock but things may be getting a little worn - dizzy speaking. Unfortunatly, I have no idea what is worn or what needs replaced- or even if it is worth bothering with!

I'm thinking of upgrading? to an electronic ignition and read a ton of info here and elsewhere but I'm dizzy from all the options. So here's my question:

Is there a later NEW Toyota dizzy that I could put in? One with electronic ingition? If so, which one? Or- If there is a "drop in" that someone has out there, who?
 
I too was having problems with my stock ignition and after a week of having some of the same problems as you went to a DUI from Man-a-Fre. Took 20 minutes to install and started right up! No more points to worry about and I can get parts for it locally. Had to make my own wires vs paying out $90 for premades, which saved my $50. I would go this route again in a heartbeat. My old distributor had been shorting out between the housing and breaker plate causing intermittent grounding problems. Good luck in choosing.
 
i went with dui drop in one wire hook up and a plug right in the dizzy for tach great unit i have had no problems yet. parts are easy to get for it to you can get them at most auto stores. you can get it from www.performancedistributers.com
or
www.man-a-fre.com

not the cheapeast at 400 clams. but i have not tlked to a person yet that did not like the second gen dui. it opens you spark plug gap up to .55. and the will build a custom power curve for you part of the package. good luck:hillbilly
 
I don't know whether other Toyota distributors would drop in to your '68, but I suspect they would. Clearance of the cap would be a factor, too, since the later ones are larger.

I assume you know that you can convert a Toyota points-type distributor to either photo-optical or magnetic induction electronic ignition using any number of "generic" kits (Crane, Jacobs, etc.). I did my '75 Toyo dizzy 12 years ago with a Crane kit and it has been flawless ever since.
 
Thanks for the replys. I am still deciding on which way to go. Money is no object (only when it comes to my cruiser) so I could go the $400 + new wires route. But that is a lot of clams.

While at the MAF website, I came across the OEM dizzy with vac advance. I might get one of those... why? well don't know realy execpt its a Toyota part and it'll "look" great. That along with a new snappy ND coil and I'll be good to go. I'll save $100 that way and while I'm adjusting the gap in the future, I'll be swearing at my self for not going with fully electronic in the first place.

So I'll need to make a decision, points or no points.
 
X2 on the suggest to contact Mark A. (65swb45) Your '68 should already have the desirable vacuum advance distributor (does it have the octane adjuster on the side?). Mark can probably set you up with a new dissy + pertronix. But, it sounds like the dissy is worn out and the pertronix won't fix that. Jim Chenoweth (FJ40Jim) rebuilds these distributors. When the bushings wear out, the rotor rocks within the dissy and you can't be sure that each wire is going to get a spark. Finally, I have a few used ones and I can send you one for cheap but you won't know what you are getting -- they might be worn out too. HTH.
 
rgentry said:
X2 on the suggest to contact Mark A. (65swb45) Your '68 should already have the desirable vacuum advance distributor (does it have the octane adjuster on the side?). Mark can probably set you up with a new dissy + pertronix. But, it sounds like the dissy is worn out and the pertronix won't fix that. Jim Chenoweth (FJ40Jim) rebuilds these distributors. When the bushings wear out, the rotor rocks within the dissy and you can't be sure that each wire is going to get a spark. Finally, I have a few used ones and I can send you one for cheap but you won't know what you are getting -- they might be worn out too. HTH.

Not to take away from any of the other guys, but if you send your diz to Jim C and have him rebuild it you will be fine. As RGentry said, you probably already have a vacuum advance diz which is desirable. Might have him put in the Pertronics(sp?) at the same time. I went with a full electronic "Big Cap" Toyota and sent it to Jim to check it out. I was very pleased. It came back with a spec sheet.;)

JMO

Ed
 
Back
Top Bottom