Getting a overhead subtank console from OZ.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 22, 2006
Threads
157
Messages
1,009
Location
Oregon
cool! I think I would like to have one of those someday but would probably would make sence to get a Subtank first. Don't really care about the altimiter. I think I'm going to go with the Laptop GPS topo maps mounted like it is in cop cars for my navigatoin, but hey one more dial never hurt.:cool:

Gratz on the win!
:cheers:
 
On my 96 this is one screw that holds the upper sun roof control facia on, remove that, then it needs to be gently pried with a flathead screwdriver, then you have 2 screws and the harness connection that need to be removed.

The console is held on by 4 bolts, 2 where the sunroof controls mounted and 2 up near the windshield. The captured nuts near the windsheild are there under the headliner just mount the sunroof ones first they poke your holes in the headliner.

BTW I have 2 factory bolts for the holes near the windshield if you need them. I had to use longer ones since they didn't fit my 96. I had to use an earlier console to get it in tan.

Hardest part will be to get the wiring done. Let me know how that goes. I have a harness made but can't figure out how to get it from the console to to DS kickpanel .
 
On my 96 this is one screw that holds the upper sun roof control facia on, remove that, then it needs to be gently pried with a flathead screwdriver, then you have 2 screws and the harness connection that need to be removed.

The console is held on by 4 bolts, 2 where the sunroof controls mounted and 2 up near the windshield. The captured nuts near the windsheild are there under the headliner just mount the sunroof ones first they poke your holes in the headliner.

BTW I have 2 factory bolts for the holes near the windshield if you need them. I had to use longer ones since they didn't fit my 96. I had to use an earlier console to get it in tan.

Hardest part will be to get the wiring done. Let me know how that goes. I have a harness made but can't figure out how to get it from the console to to DS kickpanel .

How many wires are you running from your harness to the kickpanel? I just did a autodim mirrior with temp sensor. I ran 2 wires in the headliner down the c pilar and into the kickpanel. At the upper c pillar I crossed over inside and ran wires down under the weather stripping. It was very easy. Unscrew your sunvisor and grab handles and it will make it a bit easier.

I did not think there was much to the overhead console wiring? Subtank sending wire, light reostat control. The sunroof controls are switched over. The altimeter is a stand alone unit. What else is there?
BTW I would be happy to pay for your bolts. Nothing like having OEM parts:beer:
 
You'll need to cut off the existing plug housing and use a Molex or something. It's mate is not sold by Toyota.

Let me know what you think about the visors. I had a tan set modified and recover, its an ok job. I ended up ordering a set from Mot also.

You shoudl get the bolts with the console because they don't easiler fall out of the console.

ECU was ok once I understood what the hell I needed to do. Especially with all the info posted on it and knowledge on the forum. I chose to use the 2 extra radio plugs for the backlight, ground and 12v+
 
To route the wire I removed the DS handle, sun-visor, lower portion of the dash (that has the fuel door/ hood releases) and the middle portion of the dash. The hardest part was getting the harness from the dash to the pillar. All I did was drop a shoe string through and then tied one end to the harness. Not bad, just a tight area to work in (pic one). The harness fits snug along the pillar and up into the headliner (pic two). With the sun-visors and associated parts off the harness is easy to push up from the windshield into the headliner (pic three). I didn't take a picture of it but to get the harness into the area the console covers just pulled down the headliner ever so gently. And you're done routing.

When I made my harness I used a material called Varglass sleeving (much like this: http://www.skycraftsurplus.com/index.asp?PageAction=VIEWPROD&ProdID=929) Not really necessary, normal sleeving would have been fine. Its just what I had.

Alright, here are the pics:


pic one:
P1010868.jpg


pic two (sorry about my fingers):
P1010857.jpg


pic three:
P1010861.jpg



Here are some more pics that might help out:
P1010864.jpg

P1010862.jpg
 
Last edited:
Back
Top Bottom