GE Nighthawks

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I'd like to know where you get a set of high and low beam HIDs for $150. HIDs have a ballast that must be installed and the associated harness, etc.. did he get a complete kit for that price?

They were $150 for the Highs and $150 for the Lows. I will get the info from him so I can pass it along to you guys. They came with everything needed as far as I know and they looked very good! I was shocked too since it seems like the last time I priced HID's they were around $500 for each set. I do know for a fact that he had the HID control box that pluged into the harness (is that what you meant by ballast?). And he didnt mention needing to purchase anything else.
 
Using a HID "retro" fit kit in a stock housing is a very bad idea. Cary and I may diagree about the usfulness of filtered halogen bulbs but there is no question HID's should not be fitted in a standard or even free form light housings. The point of light is not in the same position with a HID which leads to a horrible light pattern and is severely scattered. For on comming traffic it is absoultly unacceptable, not to mention they are illegal for that exact reason.

I cant give you an answer since I don't know for sure, but I think it's the factory glass. I dont remember any scattering of the light pattern since it seemed about a million times better than stock *(and looked the same as a car with factory HID's)* but I didnt install them so I'll find out and let you know.
 
Unless you get the 930's (Super Rally/available in fog as well as driving/spot). ;)

That's what I need. I need fog light for close range. I can't see anything close by like 20 feet of the car. I can see OK further. Closer that I am having problem. So, I guess I need fog light like I used to have one with my Matrix. Can you point me where I can buy?
 
kenny, the beam pattern is wrong no matter what you may seem to "see" but may not be that much of an issue due to the greater light output. I tend to agree that a HID retro fit is a huge improvement and myself would like one. The problem is they are illegal in all states because of the HUGE glare to on comming traffic. I've seen it in person and if you don't belive me go drive towards your brothers ride and see. The only way you can get a HID retro fit kit to work properly is with projector housings. I also remember around 2000 when the kits sold for $500 or so but if you notice they disappeared really quick because of new laws aginst them. The new ones on ebay for $150 are there becuse 1) the technology is cheaper and 2)not may people buy expensive stuff that can only be used for shows.
 
kenny, the beam pattern is wrong no matter what you may seem to "see" but may not be that much of an issue due to the greater light output. I tend to agree that a HID retro fit is a huge improvement and myself would like one. The problem is they are illegal in all states because of the HUGE glare to on comming traffic. I've seen it in person and if you don't belive me go drive towards your brothers ride and see. The only way you can get a HID retro fit kit to work properly is with projector housings. I also remember around 2000 when the kits sold for $500 or so but if you notice they disappeared really quick because of new laws aginst them. The new ones on ebay for $150 are there becuse 1) the technology is cheaper and 2)not may people buy expensive stuff that can only be used for shows.

The HID swap may be illegal, but it is a HUGE improvment over the OEM bulbs. The pattern looks good from the drivers seat, but I cant say I have passed my brother on the street. (Kenny and I are brothers, we are taking about my oldest brothers LC)
 
The HID swap may be illegal, but it is a HUGE improvment over the OEM bulbs. The pattern looks good from the drivers seat, but I cant say I have passed my brother on the street. (Kenny and I are brothers, we are taking about my oldest brothers LC)

Hijack: That is one sick 4runner in your avatar, man!! Hijack off.
 
The HID swap may be illegal, but it is a HUGE improvment over the OEM bulbs. The pattern looks good from the drivers seat, but I cant say I have passed my brother on the street. (Kenny and I are brothers, we are taking about my oldest brothers LC)

If you are trying to get HID output skip the HID kit, get the HIR 9011 bulbs and put them in the low beams. Here is the proceedure to do this:

http://www.bmwe34.net/E34main/Upgrade/More_light.htm


For $60, you will have 2500 lumens in the low beams with a Color Rendering Index in the high 90's (compared to HID's being in the 70's or 80's). (Most HID kits have 2800-3000 lumen lamps). More importantly, you will have close to the property lamp focus (the filament lengths are slightly different between the 9011 and 9012) so there will be far less glare. You will end up with more light on the road than an HID swap with the stock housings and they will be kinder to oncoming drivers.

Also, you have PROPERLY adjusted your headlamps, right? If not, go to www.danielsternlighting.com and read the procedure to do this. Note the built in adjusters in the 80 are not necessarly accurate, so you need to do the wall method to be accurate.
 
That's what I need. I need fog light for close range. I can't see anything close by like 20 feet of the car. I can see OK further. Closer that I am having problem. So, I guess I need fog light like I used to have one with my Matrix. Can you point me where I can buy?

You need to check your headlight alignment first. I would be very reluctant to suggest you run fog lights on a normal basis. The additional light close in will cause you pupils to dialate resulting in worse vision for objects down the road. This of course changes in rain and slow speeds as it seems the road just eats up the light then.
 
Good link, Cary. That's the mod I did to get the High Beam HIR's to fit my low beam plug and the light is absolutely awesome.
 
The Nighthawks are noticably brighter than the Sylvania bulbs they replaced. They are street legal in California. I would never consider using my Hella 4000 driving lights on the highway - just back roads and such.

As for HIR/HID, solutions, I do like like being blinded by some yahoo who has exceeded legal limits - it is inconsiderate of other people - and I won't do it just because it can be done.
 
As for HIR/HID, solutions, I do like like being blinded by some yahoo who has exceeded legal limits - it is inconsiderate of other people - and I won't do it just because it can be done.

I've yet to be flashed in over 5,000 miles of driving, at least half of that in the dark with lights on, with my HIR high bulbs in the low plugs. Do you know what the legal limit is????? I understand a retro-fitted HID kit in the 80 series housing might exceed "legal limits", but the HIR bulbs DO NOT exceed "legal limits".
 
Just to set the record straight, none of the discussed mods meet with dot requirements. When we swap in the HIR bulbs, we have taken them outside their original design. When you do a 9006 to 9005 swap (or 9006 to 9011 as it may be) that does not meet the DOT specs. HID kits do not. The only way that you have a fully complaint DOT lamp is to use a housing that meets DOT specs with the bulb it was originally designed for.


When we do the HIR swap, it works well because the filiment alignment is exactly the same as the stock lamps, and the length of the filaments are nearly identical. Even when doing the 9011 swap into the 9006, we are still doing pretty well because even though the 9011 has a 21mm shaft instead of 22mm, the extra O ring keeps it aligned. The filiment placement is the same, with a very slight deviation in its length.

HID swaps do not work well because the arc of the lamp is a different length than the incadecent lamps, and worse yet, the arc location is not even close. This leads to tons of scattered light and is the reason I do not recommend them.
 
HIR's and Slee Harness upgrade

After researching this site for hours I decided to invest in a set of both high and low beam HIR's. To bring out the best in them I also purchases a Slee Upgrade Harness. The difference is simply amazing! I purchased my HIR's from one of the vendors offering a group buy on this site. Since then I have contacted my local AgPro John Deere dealer who carrys the low beams for half of what I paid. No complaints here though, the return on my investment is worth every penny. Go with the HIR's and upgrade your harness, you won't be sorry. Just my two cents. By the way, thanks to everyone on the site that posted info on the HIR's!
 
Back
Top Bottom