Garage cleanup

[FLYINGLOW]

Now that im done the SOA I need to clean out the garage...

I have the front axle i pulled out minus the 3rd, calipers and axle shafts to get rid of. Its small patern knuckles. $100

Set of custom rear springs, nicely arced for about 2.5" lift SUA. Lengthened similar to 55 springs. Rode very nice and worked with a stock rear shaft. Did i mention rode very nice? $125

Lots of F and 2F stuff, let me know if you need anything.

Theres more stuff but i can't think of anything right now.

More stuff to add:

Jump seats $20

Oxygen and acetylene regulators $80

2F double pulley set $50

2F air filter housings, I have 2, one is powder coated. one is gone to the scrap pile

2F short block for rebuild, its going for scrap if nobody wants it. gone for scrap

2F crank shaft.

2 sets of ambulance doors, usual rust.

K&N filter for stock 2F air intake

2F electronic ignition set up (saw the dizzy last night, coil should be around)

I'm open to offers, especially if I haven't listed a price.

 

[FLYINGLOW]

I have 2 spare t-cases, one is in peieces and can be seen, the other one I replaced the bearings and seals in. It was run for a couple months. They are both one peice cases with 16 spline input gears. I would like to sell one of them. Price negotiable.

 

[FLYINGLOW]

Offers on anything?

 

[Dieseler]

Were on the Island are located

 

[FLYINGLOW]

Were on the Island are located

Sorry, Ladysmith. Its just south of nanaimo.

 

[jinzuke]

do you have any 40s to go with that. I could use a good 40.

 

[seapotato]

there's a 42 on used nanaimo. looks typically mediocre, but not too bad.

 

[Dieseler]

I will see if my son can head down your way to look at the parts and throw an offer out to you on the axle and springs

 

[FLYINGLOW]

I will see if my son can head down your way to look at the parts and throw an offer out to you on the axle and springs

Ok, email me cruisermark@shaw.ca Where's he at?

 

[FLYINGLOW]

do you have any 40s to go with that. I could use a good 40.

Between Abel and I we probably have enough parts to build one... Only gas engines laying around though.

 

[Toshi38]

what happened to the 3B out in the goat barn?

 

[seapotato]

what happened to the 3B out in the goat barn?

it now resides in the excressence.

decided it would be far easier to access my spare parts if I put them together into something that rolls and drives...

 

[hellbent40]

any double groove water pump pulleys for a 2f????

 

[FLYINGLOW]

any double groove water pump pulleys for a 2f????

Theres a very good chance...

 

[FLYINGLOW]

any double groove water pump pulleys for a 2f????

Do you need a set or just the water pump pulley? I have a set. $80

 

[FLYINGLOW]

Heres some pics of the springs, they ran nicely with a 2.5 lift springs up front, 8 leaves and are 46" long mains. Don't know how that compares to 55 springs but the top 3 leaves were replaced with new ones by Hub City Springs in nanaimo. I can dig up some pics from when I installed them and pics of the truck in action. Worked with a stock rear drive shaft.

 

[hellbent40]

just the pulley

 

[BC40]

If Dieseler doesn't take the springs, I'd be intersted.
Stock should be almost 44" flat length, so these are 2-3" longer.

 

[FLYINGLOW]

just the pulley

I think id rather sell them as a set.

Anyone need a 4 spd flywheel? Its going for scrap otherwise... Its cheap...

 

[lineman_fj40]

Same size roughly as 60 rear spring