FZJ80 transmission problem/question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 8, 2007
Threads
20
Messages
121
Location
St Augustine, Fl.
Ok so I've had no problems with my 80 transmission ever and have 250k miles. It's got the A442 transmission and is regularly serviced.

Now for the problem....it can't seem to figure out what gear it needs to be in and shifts up and down sometimes 2 gears at a time. Fluid level is good. Throttle closed switch is working properly. Engine free revs and runs fine if I manually shift through the gears. In D it sometimes starts in 1 sometimes 2 sometimes 3. It's very random. I put my MAC scantool on it and the truck has no dtcs. Trans doesn't slip just can't seem to figure which gear to be in.i have a video if I can figure how to post it...

Bad TPS?
 
Watch "Weird shifting Land Cruiser" on YouTube
Weird shifting Land Cruiser:
 
Check your TPS?
 
With the scan tool on it it has a good reading. Is there another way to test it?
 
So I went out today and rechecked everything. I adjusted the tps in 1/32 increments to see if it would shift properly. I also rechecked the throttle cable/trans cable adjustments. Everything is right....still shifting to soon and doesn't want to stay in one gear. No changes at all..
Some help would be great
 
Still need help with this. Checked codes again. I got nothing. Serviced transmission including filter. No change. Adjusted the TPS no change. Ordered a new TPS from Dan. Should get it next week. Fluid looked excellent no sediment in pan and I couldn't get any friction material to even wipe off the pan it's so clean. My friend who works for Freightliner thinks it's a pressure control solenoid in the trans going bad. I really need some info from a Yota tech here.
 
Are your dash lights working correctly P,R,N,D,2,1 ?
If you hold in in 1, does it stay in 1 or does it shift up?
In reverse, does it seem to go into neutral at times?
 
Unplug the shift solenoid harness at the trans(just above the NSS on the trans (drivers side on the side of the trans, plugs in from the top)

Then take it for a drive, manually shifting...

L will be 1st
2 will be 3rd
D will be D

If this checks out, it's your shift solenoids or the wiring...

Next check the wiring plugs just above the starter, they're a pain in the ass to get to...

Has your OD light flashed at all?
 
No flashing lights. No DTCs. Works fine manually shifting. Does not advance or do anything bizarre when manually shifting
 
Thanks yall. It's unusual to me that it would do it in every gear and this started suddenly. It operated properly one day next day I drove it it did not. I would think all solenoids would go bad at the same time. I was on the highway the other evening running 70 and was about half way on the throttle pedal. I pushed it to the floor and it did not change rpm or do anything. Thats why I had leaned toward tps.
 
It almost sounds like the lockup solenoid...its locking and unlocking the torque converter...

Also, there are 4 solenoids in the 442f, but only 2 of them control gear changes...the others are timing and lockup...

If only one goes bad, it will give you the issues you're seeing...

Have you looked at the link I posted? Or the wiring? Or trying to unplug the solenoids and manually shift?

The link is the trans FSM and is VERY helpful for diagnosing.

Try to test the resistance of the TPS via the FSM, or even just unplug it and see if it changes things...

It could also be one of the speed sensors...

Try checking things via the FSM in the link and report back, like I said, I've tested everything and I'll try to help you out as I just got mine fixed and its fresh in my mind, and I know how annoying it is!!
 
@Yardboy - this is the thread with the link (above)
 
Back
Top Bottom