Front Brakes Locking up

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 18, 2006
Threads
4
Messages
12
Allright,
Hey guys and I love the site. I have been reading for a while and now the problem with the truck and I figured to ask in my first post here.

Yesterday as I am driving in to work the front brakes locked up and I limped the FJ 80 93 in the parking lot. It looks as if the calipers are not releasing the pads causing to expand and lock up the front brakes. After several hours I cranked it up to take it to the shop and it was fine. I drove it about 5 or 6 miles and no problems. The shop replaced the pads and drained the cooked brake fluid out, and said the rotors looked OKAY. So Im on my way on my 40 mile commute and it starts locking up again. Anyone had problems with this before. I had it towed back to the shop and we are looking at replacing some of the lines and bleeding the whole system.

Any help would be appreciated.
 
Did you put power steering fluid in your brakes? Something causing the lines to swell?

Nothing set this off? You didn't do anything under the hood before this? How is the master cylinder?
 
Nope, No power steering in the Master Cyclinder. I have run the truck several 1000 miles No problem. I checked the fluid when we bled the brakes and it didn't look to good. I burnt up the pads the first time it happend and hope I haven't done the same again. Is there any adjustments you can make on the calipers?
 
After we put the New pads on, after the first time this happend we bled the brakes to pump up the system with clean fluid. At this point it looked muddy and black?

Is there a couple check point to bleed to see the preasure in the system?

After the brakes cool, I get more pedal and they release, It is just when they are locked and hot that the pedal just stops hard.
 
You have calipers on the left and right sides. It is not uncommon for one side to have a sticky caliper that would cause premature pad wear or pulling to the side that was sticking. It seems unlikely that BOTH sides would start sticking/unsticking at the same time.

Are you having problems on both sides?

-B-
 
I noticed the drivers side was smoking but not the passenger side, although both sides had worn out pads.
 
What can you do for sticky pads? If this is common is there a easy solution?
The easiest thing to do is to buy and install remanufactured calipers and install new pads.

You can buy a rebuild kit for around $20 (does both sides) from CruiserDan. Rebuilding them yourself is not difficult, especially if you have compressed air to aid in the removal of any stuck pistons.

Or give Dan a call and order the calipers and pads, jack up the truck, pull the wheel, R&R the caliper, repeat for the other side, bleed the brakes and be done with it. I'm guessing you are a 1 :banana: DIY guy so you might be more comfortable giving this one to your friendly mechanic (... it is your brakes afterall...)

-B-
 
Last edited:
Had this happen with my old 4runner, started out very intermittent, then more often. It turned out to be the master cylinder not releasing pressure. If your front caliper pistons slide alright, I would suspect the master cylinder.

Doug
 
Im a DIY when it comes to some stuff, some stuff I outsource due to time and situation. That beeing said I need contact info for CruiserDan to get me some calipers, and any one got the Hook up on a Master Cyclinder????

Rhoads
 
PM CruiserDan or call American Toyota and ask for Dan in parts. They are in the Advertiser's section here on 'Mud. (1-800-432-6668) He will also have the master cylinder. Best place on the planet to get your new Toyota parts.

-B-
 
I've been experiencing this w/my 1990 HDJ81 lately. Odd thing is it's worse on the highway when I'm not using my brakes at all. The brakes just slowly start to apply themselves until the truck is fighting itself to keep going forward. It was really bad today. I'm suspecting ugly brake fluid and since it's the easiest and cheapest thing to do I'll be flushing the entire system. Unfortunately I've toasted my rotors in the process- ah well, I need to do a complete axle service anyway...
 
Well, quick update. I flushed my system and YAY! brakes function as they should now. Cheap and easy!
 
You know, the rotors have stopped pulsing as well. I think I heated them up so much that they straightened out! I'm changing them out anyway as they are most likely too thin now.
 
A friend of mine had a problem with brakes not releasing. After replacing everything else, he began replacing hoses. He found a steel bracket that held the hose had rusted and swelled internally, pinching the hose off. This probably isn't your problem, but shows that you really need to look at everything before you start spending money.
 
Back
Top Bottom