Flipping my springs

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 14, 2005
Threads
8
Messages
75
Location
Klamath Falls, OR
Ok, so I know that this is a simple question, and it will probably make somebody grumpy because I am sure there is information on this subject easily accessible all over the place. That being said I am still a rookie and was un-able to locate the info I need so here is the question. I have a '71 fj40 (my first cruiser) and I am looking to flip my rear leaf springs to increase my wheelbase and make room for 35" tires. How much will this increase the wheelbase? Will I need to replace any parts other than the obvious bushings? I have just recently replaced the shackles so I am pretty familiar with that end of business but I was told that the end of the spring attached to the spring hanger can be a little tricky. Any advice or directions on where to find more information would be greatly appreciated.
 
Honestly, the spring reversal things is kind of stupid, imho.

You'd be much better off replacing your stock FJ40 spring with some FJ55 rears (all the way aroud!) and you'll get a more comfortable ride, better articulation and you can manipulate wheel base a little more.

If you don't mind changing your spring hangers to the later style (larger bushing units) you could use FJ60 rear springs all the way around. If you want a little more lift, use one or two of the front FJ60 springs in the mix since they have more arch.

The advantage of using the 60 series units is that they are more abundant. Just ask if anyone here has some from doing a spring change on their 60 and they'll likely sell you their old ones for about $20 a piece.

:cheers:

~John
 
I just finished doing what you are talking about and I am a rookie as well. I believe you get about 4 inches of wheel base but let me tell you doing this is not as easy as what it sounds. It is not hard just make sure you have all your tools and bushings and new spring pins ready. unless your front bushings have been replaced recently you are more than likely going to need a torch to burn them out before you can even think of getting the spring pins out. I ordered the greasable kind from CCOT plus the new bushings for both sides front and rear and it was like $69 shipped. I would like to have had them when I started the whole thing rather than waiting. Also you will probably need new u-bolts and now is a good time to redo the rear brake lines since the axle will be out. You will also need some shims to help correct the pinion angle and you will need to redrill the military wrap spring. Let me know if you have any questions it took me about 6 hours to do the whole project if you have everything you need there to do it all at once.
 
this is what i've done, and what i'm doing.

IMO, on a 40 a spring flip at both ends is'nt a bad idea at all, longer wheelbase,better handling,more stable. i see so no downside to doing this.


i've got a modified rear spring set up using the top two leafs from the rear of a 62,and the springs from a 2.5" skyjacker lift. flipped,there's about three inches added there.
the fronts are going to be the top two leafs from the rear of a set of fj55,combined with the front springs of the skyjacker lift. i am told the 55 springs alone will extend the front forward about 3-4"
streching the wheelbase anywhere from 6-4"

my .02
 
Elaborate please.


Mark...

Gosh, Mark, we covered this on the LCML something like 10 years ago... is there any real need to cover this topic again?


~John

(edit - oops talking about SR up there. Read the rest of my post: I advocate doing a spring swap for longer springs... and you are perfectly well aware of the benefits of longer springs.)
 
the main thing to know is just use a torch on the end of the spring pin that you unbolt and just keep heating it till it is red hot time depends on what kind of torch you use. eventually the bushing will burn out and then you can almost just pull the spring pin out by hand. If it is stuck you can hit it with a sledge for an hour and never move it
 
Sure, a longer spring is better than a shorter one. But he has the '40 springs in hand. I run '55 rear springs front and rear on my leaf sprung '40. but how many guys have those lying around?

So longer springs are better. Yep. So what? How does that make ot stupid or in any way not good to reverse the existing springs in search of a longer wheelbase?


Mark...
 
deleted by
Mark...

My reasoning is thus: for a similar amount of time and effort and just a little more cost (using used springs), one can get the benefits of a longer wheel base AND longer springs. Win, win, win & win (the third one is for ride quality, the fourth one is for articulation).

That's it... pretty simple. Get much more bang for your fabricating buck.

Note that I also said "imho" in my previous post.

:cheers:

~John
 
Last edited:
I deleted the message that John quoted in his respinse, 'cause it seemd to me that it came across a little more combative than it needed to.

While I agree with all of the benefits stated woth the longer springs, that still doesn't change the fact that reversing the stock springs gains you a better ride, better wheel base and better articulation than the stock setup. It cost nothing except a few bucks for the new center pins and some time (and bushings if needed of course). And like stated... He has the stock springs. He doesn't have the rear springs off of a pair of Pigs.


Mark...
 
My reasoning is thus: for a similar amount of time and effort and just a little more cost (using used springs), one can get the benefits of a longer wheel base AND longer springs. Win, win, win & win (the third one is for ride quality, the fourth one is for articulation).

That's it... pretty simple. Get much more bang for your fabricating buck.

Note that I also said "imho" in my previous post.


I don't think that flipping springs is fabricating mainly just replacing some parts that should have already been done, ubolts and bushings, and just putting the springs back in backwards I did mine for cheap if I would have gotten any form of new springs it would have gotten costly really fast. I do agree though that the 60 springs are a great idea when you get ready to start actually fabricating
 
It cost nothing except a few bucks for the new center pins and some time (and bushings if needed of course). Mark...

Is it really that simple? Now you've got my attention. Are driveshafts and brakelines not an issue with a simple flip of the 40 springs?
 
Is it really that simple? Now you've got my attention. Are driveshafts and brakelines not an issue with a simple flip of the 40 springs?

yes the drive shaft needs addressed you might be able to get away with it but it is doubtful and brake lines need addressed to especially if you are adding any form of lift.
 
Drivelines are an issue. As are brake lines.

I didn't toss that in just because both approaches require the same in terms of shafts and brakelines. (The axle shift is virtually identical with reversed '40 springs or with '55 rear springs).


Mark...
 
Brake lines; Use BH3809s... 22 inches long.

Driveshafts, cost about $100-$200 to get lengthened, depending on your locality.

You will have to relocate your shock mounts. In the back, weld new pins onto the backside of the shock mount crossmember. Up front you can make new towers, reverse the pins in your existing towers, or cut the tab off of the axle and turn it around/shift it a little. I lean toward makeing new towers (or using the ford F250 towers) so that you can also fit longer shocks for greater travel. In the rear moving your shock pins inward as you relocate them to the rear of the crossmember will also make room for longer shocks.


Mark...
 
Back
Top Bottom