fj80 engine swap mayby

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 12, 2008
Threads
3
Messages
6
Location
Knoxville, TN
i was on my way to Tenn. and my engine went south on me. I have taken to two auto shops and both have said it was more trouble than it was worth to them. My engine is a trd supercharged six cylinder. It had plent of power when running but it seems it is going to be expensive to replace. Does anyone make a V8 conversion using all stock transmision/ running gear? I need help brothers love my 80 and want to get it running strong again.
 
Have them tell you exactly what the problem is. If it's just a blown headgasket you can do that yourself.
 
trouble

they said it has some broken rings and is just ouring oil out back and smoking real bad. it also has a miss and runs like crap below 2500prm when i go above that the thing does better.
 
How would they know it had broken rings unless they pulled the head to see or if the dropped the oil pan to see?
 
BTW, first dibs on your Supercharger. You aren't going to need that paper weight anymore and would be more than happy to take it off your hands![/quote]

Then your non-turbocharged pistons, rings, wrist pins, and connecting rods can do the same thing. Don't you just love add-on forced induction!!!!! Especially the word "forced"!!!!!
 
1st, does the engine crank?
If it does, do a compression test across all cylinders.
If not, drop the oil pan and see which bearing spun.
You can probably bring this engine back to life yourself or with the help of local friendly cruiserheads.
These engines are built like battleships. You have to try pretty hard to make one un-rebuildable.
I think your shops are just being lazy, not wanting to spend the time on a 16 year old vehicle.
 
I 2nd that.. Fix yourself or find an engine out of a low milage wreck if it is rings. IMHO probably just a headgasket.
 
Are these engines too weak to be reliable with the TRD supercharger?

Hundreds (if not thousands) of these superchargers run the roads every day. I'm not sure why Downey thinks the motors can't handle it.
 
I think it is the head gasket that downey does not like..

IMHO run a thicker SCE ICS titan headgasket on it

1. for a better seal
2. lower compression a touch..
 
Check out my current thread. Don't let the dealers get you down. I was told many different things, but until I tore my motor apart they were all wrong. Well except for Robbie (Aka Powderpig). I even had my cruiser at LC Engineering for four months and they said I had cracked rings. They were wrong. My pistons in the 4 and 5 cylinders started welding themselves to the cylinder wall causing the compression loss. The rings were fine. I bet yours are fine as well.


https://forum.ih8mud.com/80-series-tech/226409-supercharged-more.html


Good luck and hang in there.
 
Then your non-turbocharged pistons, rings, wrist pins, and connecting rods can do the same thing. Don't you just love add-on forced induction!!!!! Especially the word "forced"!!!!!

Are these engines too weak to be reliable with the TRD supercharger?

Hundreds (if not thousands) of these superchargers run the roads every day. I'm not sure why Downey thinks the motors can't handle it.

I'm with you. I was typing tongue-in-cheek.
 
Lawd, have mercy. I just know you don't have 35's and a 4" lift, and are running it with the original gears?

Right?


What size tires are you running?


"It had plent of power when running but it seems it is going to be expensive to replace."

:lol: aren't awesome, designed to go 300k + motors a bitch that way? :rolleyes:

Just W8, you'll love it when you swap in another motor at the cost of thousands more than what you'd be currently replacing yers fers. Only to prolly wind up S.Cing it, and doing this all over again.





BTW, first dibs on your Supercharger. You aren't going to need that paper weight anymore and would be more than happy to take it off your hands!

Then your non-turbocharged pistons, rings, wrist pins, and connecting rods can do the same thing. Don't you just love add-on forced induction!!!!! Especially the word "forced"!!!!!


you mean there's downside to slapping a SC on a motor with 9:1 compression?


naaaa, :lol:
 
Last edited:
Back
Top Bottom