First Front Axle Rebuild Question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 20, 2006
Threads
4
Messages
26
Hello All,
Well first off thanks to Cdan for all your help, received my parts and got started today. First thing I did was have a beer as recommended by so many on the forum while I looked through all the parts then I had another. :eek: This is my first front axle rebuild on my 92 with 241,000 on her so it's time. Well I did'nt get very far along and I have a question. After removing the grease cap, the six nuts and cone washers from the flange and the snap ring I noticed that there is what I call slop between the outer drive shaft and the outer drive flange. When I grab the end of the drive shaft and the flange I can move them in opposite directions a fraction of an inch, is this normal ? Do I need to replace the outer shaft and flange ? :doh:

Any help will be great!

Thanks, I will sit and drink beers for now!!!!!
 
Don't know if it is normal, but my '92 did it even with a brand new birf. The old one had stripped out. I noticed that it is especially a pain when trying to put the circlip back on. It slides back in there. I just tension it with a screwdriver in the hole on the end. I think the slop is just accumulated between the diff, star area of the birf and axle, and any other loose spots in there. I am sure someone more knowing will pipe in.
 
Hello All,
Well first off thanks to Cdan for all your help, received my parts and got started today. First thing I did was have a beer as recommended by so many on the forum while I looked through all the parts then I had another. :eek: This is my first front axle rebuild on my 92 with 241,000 on her so it's time. Well I did'nt get very far along and I have a question. After removing the grease cap, the six nuts and cone washers from the flange and the snap ring I noticed that there is what I call slop between the outer drive shaft and the outer drive flange. When I grab the end of the drive shaft and the flange I can move them in opposite directions a fraction of an inch, is this normal ? Do I need to replace the outer shaft and flange ? :doh:

Any help will be great!

Thanks, I will sit and drink beers for now!!!!!

You talking about movement in the direction parallel to the axle? If so, then yes it's normal to be able to move the axle shaft in some. That's why there's a threaded hole in the end of the shaft, so you can thread a bolt in it to pull it out snug so you can put the snap ring on.

:beer:
Rookie2
 
Rookie2

Hello:

No, not in and out I mean forward and backwards like slop in a bad U-joint kind of movment. This is at the outer drive shaft end where the flange (drive plate) itself is located. It seams like slope in the splines!

Thanks
 
Once I took off the drive flanges on mine the outer end of the axle stub/birfield was able to move around slightly, as it was only supported by the brass bushings at the inner end of the spindle. It's normal.
 
I may not be explaining this correctily

If I held the outer drive shaft in my left hand (once removed from the truck) and set my beer down with my right hand and grabed the outer drive flange. Slid the two together as they would be when installed in the truck and rotated each hand in opposite directions back and forth (like twisting a beer bottle top off) I notice a slight amount of movement. Is any movement to much or is there an acceptable amount?

Thanks for all your comments! :idea:
 
How did it go?

How did it all turn out? I received all my parts today from CDAN (Gracias) and will be starting this process tomorrow. There are a few things that worry me an d I am curious what you did.

1) Did you separate and switch sides? I have heard you should do this but until I get in there all I can come up with in my head is :confused:.

2) If you have completed this project what would you do differently if you could go back and do it again?

3) Thank you for your posts if I find ther same movement you described I will not panic.

4) If you are not done and are in the NW and need a second set of hands let me know.

I am going to Northern California right out side of Yuba City to see my wifes family and figure I should get this done before the trip.


:beer:HEFE
 
Joe,

The 92 flanges are known to strip when they get some slack worn into them. Once you have slack, you are also wearing the axle itself ($$$), so I'd put it together with new drive plates to minimize the slack. They're cheap, so good value - especially compared to wearing the splines on the axle and replacing THAT. Be sure you put grease in the spline/drive plate interface on assembly.

DougM
 
Drive Flange Looks Bad Once I Found my Glasses!

Hey Fellas,

Thanks for the help! I just about have one side put back together, I have stopped at the drive flange for now. At this point I will be taking IdahoDoug's addvise and getting some new drive flanges, the originals are very loose. Drive shaft upon examination looks to be O.K. but wondering if I should replace them also $$$$?

I did not separate two switch sides, I think maybe I should have! They did'nt look to worn to my naked eye.

HEFE,
Next time I will have more rags and paper towels on hand and find a better brass drift (larger I mean) mine is rather small.

IdahoDoug, thanks for the help!

Joe
 
At this point I will be taking IdahoDoug's addvise and getting some new drive flanges, the originals are very loose.

Assuming you are going to get the drive plates from C-Dan, be sure to ask him if you can use a drive plate for the '97 model.

-B-
 
Back
Top Bottom