Fine Spline Upgrades?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 2, 2004
Threads
81
Messages
602
Location
Western Slope, CO
Well I broke my 10 spline pinion this last week...:mad:

Guess it's not if it happens but when, I'm kind of on the fence about which direction to go from here. Should I just step up to the fine spline pinion?

Also is this just a matter of changing out the R&P and flange? I have a rear locker too, can this be used with the new R&P?

If I decide to look for a complete third member, what years came with the 27 spline? And did they have the 4.10 gears?
 
1978 only 40/55 ring and pinion were 27 spline...



1988-1990 FJ62 front and rear are 27 spline 4:10 and will work..



The fine spline ring and pinion are compatible with the carrier assembly or locker that is in the diff. Yes, you will just need to get a fine spline companion flange for the gear set.


Why did it fail?

Did your rear drive shaft bind up from axle wrap?


What does your anti-wrap bar look like?
 
Ok don't flame me for this (I know better) But because I was using lifted springs in the rear I didn't see a need for the anit-wrap bar...:o

I was attempting to get up a steep bank, started to bounce, didn't get off the go pedal soon enough and bam!

Guess this gives me a good excuse to go with those higher gears AND build a anti-wrap bar huh?

what are my options on vendors? I have heard good things about Kurt.:cool:
 
Ok don't flame me for this (I know better) But because I was using lifted springs in the rear I didn't see a need for the anit-wrap bar...:o




Are you going to install one now?



Re-gearing is a pretty significant investment in time and money....I sure would read up on them out here and then build one....They are a must have item with a spring over suspension system.




What ratio are you looking to change to?

4.56?

4.88?
 
No worries wtmtnterror! You would have broken it that way whether it was fine or course. Poser is right about the axle wrap being the real problem. He beat me up on it too! Just call Jeremiah from Proffits Cruisers. He'll send you an entire diff for $100, course splined, just transfer your locker from yours to the new one, drop it in and BUILD A TRAC BAR! There are some good plans out on the board somewhere using tractor 3 point hitch arms that you can buy from any tractor supply store.
 
Poser,
I do plan on building an anti-wrap bar if I keep my toy axles. Just looking at other options right now, Considering what it will cost me to re-gear two axles and add a front locker $$$
Looking at 4.88s :grinpimp:

Thsorens,
Thanks for the tip on the diff, I was just looking at one on e-bay last week with one bid! :doh:
 
Poser, I do plan on building an anti-wrap bar if I keep my toy axles. Just looking at other options right now, Considering what it will cost me to re-gear two axles and add a front locker $$$
Looking at 4.88s :grinpimp:


Does not matter if you keep Toyota axles or switch to something else.....you will need something to stop axle/spring wrap....unless you reconfigure your suspension.



I think that FJ40Charles out here had a 4.11 fine spline diff he was selling....he may still have it.



Replacing the third would be the quick fix...and far less monies than a re-gear...




Poser is right about the axle wrap being the real problem. He beat me up on it too!


Beat you up?


By stating facts about a failure based on what I have witnessed?



Buck up little campers....:crybaby:



;) :beer:
 
Beat you up?

By stating facts about a failure based on what I have witnessed?

Buck up little campers....:crybaby:



;) :beer:

I'm bucked up poser! If I remember right, I asked why my pinion broke and you said "show me a picture of your trac bar" To which I replied "You are such a smart ass Poser" To which you replied "Rather be a smart ass than a dumb ass"

We expect you to beat us up on this stuff poser! We are not worthy! :lol: It's all good......
 
Have R&P sets gone through a big price increase, or aren't they still available for around $200. ea.?
 
Back
Top Bottom