Exhaust ???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

TEXASLAWMAN

SILVER Star
Joined
Oct 20, 2005
Threads
68
Messages
479
Location
TEXAS
Website
www.myspace.com
Was:Exhaust ?? Now: Results of exhaust changes.

My cats are leaking and need replacement. So I ordered a new high flow cat. I want to keep my stock cats so I plan on cutting them off and placing a section of flex hose in their place. Otherwise the muffler shop keeps them. My question is will it hurt anything to drive it like this for a hundred or so miles or a few days???
 
Last edited:
I dont know about Texas but in Oregon we have DEQ which is for emissions and they wouldn't even put my old tahoe on the rack because I removed the cat. IMHO, staight pipe wouldn't hurt it, may get a check engine light.
 
IMHO...

If you are going to be working on the exhaust at all DIY it.

Get some straight pipe and the cat. cut out the old one. Get the length right (leaving room for a slip) on the pieces of straight pipe you may need to go between the new pipe and the existing system. Get the pipes expanded. Assemble it temporarly to mark cat and y pipe for location... Got to a welder or use yours if you have it and weld the cat to the Y pipe and new sections of pipe. Then use a band clamp where the rear new piece of pipe attaches to the tailpipe.

I have my stock cats on the floor of my garage.. I need to find a place that buys before I move.
 
I dont know about Texas but in Oregon we have DEQ which is for emissions and they wouldn't even put my old tahoe on the rack because I removed the cat. IMHO, staight pipe wouldn't hurt it, may get a check engine light.

If any issues come up there have been a rash of cat's sawzwed and stolen so that wont be a problem. They cut the cats off my brothers 4runner in his apartment parking lot broad daylight a few months back!!! Just didnt want to hurt the truck by driving it that far.
 
The worst you will get is degraded performance and a CEL - no permanent damage.
 
Well this is not good got the 2.5 ID flex pipe and exhaust clamps removed the cats. The freaking exhaust pipe in front of the cats is bigger than 2.5" the rear is fine. What gives??? How far can I drive it like this without hurting something??????
 
Check your y-pipe for cracks. Knock off the paint/rust in the inside of the crotch.. Probably a giant crack there. The ID is the same on the front pipe as the rear they just used a thicker wall for that section.

Do you have the new cat yet?
 
Check your y-pipe for cracks. Knock off the paint/rust in the inside of the crotch.. Probably a giant crack there. The ID is the same on the front pipe as the rear they just used a thicker wall for that section.

Do you have the new cat yet?

I all ready welded the y pipe earlier this year. No I dont have the cat yet. I was going to run it for a few days without the cats just to see what differance it made in mpg and hp using my scangauge and dynolicious. And then again with the high flow cat in. I got 2.5" flex pipe and it will not go over the thicker wall. I need to take it to a muffler shop and have them weld a pipe in since I have no welder right now.
 
I've only bypassed cats on OBD1 80's. Always seems to produce a tad bit more noise and a little better top end power. As others have mentioned, your OBD2 will throw a fit and turn on the idiot light. Other than that, I don't foresee any long term issues.
 
I've only bypassed cats on OBD1 80's. Always seems to produce a tad bit more noise and a little better top end power. As others have mentioned, your OBD2 will throw a fit and turn on the idiot light. Other than that, I don't foresee any long term issues.

I wasent worried about no cats. My plan was to use flex pipe till the cat I ordered arrived. Now that the flex pipe isnt big enough Im haveing a pipe welded in untill the cat gets here. Ill take it to my freinds shop and have him do an emissions test to see what I get with no cats just out of curiosity. Only thing I was worried about only having about a yard of exhaust pipe now untill i get to the muffler shop. The mechanics Ive talked to say as long as I have a foot of exhaust it will be fine to drive down there.
 
Last edited:
You should be fine driving it to the shop. If you get pulled over, just show 'em the new cat on your passenger seat :lol:
 
Make sure it is blowing down and away from any part of the vehicle. I ran mine for awhile when I had to swap my transmission and it was kinda aiming at a body mount. Needless to say the body mount started melting, and it started boilling the gas in the tank:eek:(3fe, drive side drop). This was after a I had put in a high flow cat.
 
Make sure it is blowing down and away from any part of the vehicle. I ran mine for awhile when I had to swap my transmission and it was kinda aiming at a body mount. Needless to say the body mount started melting, and it started boilling the gas in the tank:eek:(3fe, drive side drop). This was after a I had put in a high flow cat.

I called around and found a shop within 2 miles of my work that will seal it up for $20 untill my cat comes in. So 2 miles one red light at 40mph should be ok. :cheers:
 
Ok got a straight pipe in place of the cats now. I cant tell a difference in sound. Maybe because after the awfull sound with no muffler and its hard to hear over the M/T tires. The truck feels a bit more peppy. Here is the average of 4 runs with and with out stock cats.

With------------- Without

0-10mph 1.33sec-------- 1.49sec
0-20 2.97 ---------------2.92
0-30 4.65 -------------- 4.59
0-40 6.95 ---------------6.79
0-50 10.04 --------------9.48
0-60 13.71--------------12.71
0-70 19.04--------------17.72

Peak Horsepower
(I forgot to change the Drivetrain Loss percentage so the HP is low. But now I have a base dont want to change settings.)

With-------------Without
179hp 191hp


Ill post up MPG later. No cel code yet engine running smooth. Thinking of returning the cat when it comes and running a 3" cat and exhaust with downy headers.
 
Im guessing you were using a g-tech? Gain of a whole second from 0-60 aint too shabby, but still no sports car. I wonder about the power under the curve...
 
Ok got a straight pipe in place of the cats now. I cant tell a difference in sound. Maybe because after the awfull sound with no muffler and its hard to hear over the M/T tires. The truck feels a bit more peppy. Here is the average of 4 runs with and with out stock cats.

With------------- Without

0-10mph 1.33sec-------- 1.49sec
0-20 2.97 ---------------2.92
0-30 4.65 -------------- 4.59
0-40 6.95 ---------------6.79
0-50 10.04 --------------9.48
0-60 13.71--------------12.71
0-70 19.04--------------17.72

Peak Horsepower (I forgot to change the Drivetrain Loss percentage so the HP is low. But now I have a base dont want to change settings.)

With-------------Without
179hp 191hp


Ill post up MPG later. No cel code yet engine running smooth. Thinking of returning the cat when it comes and running a 3" cat and exhaust with downy headers.

That is what I'd do.. I have repaired y-pipe to 3" with no cat.. Going to become 3" with 3" high flow cat. Much later a built motor will go in with a turbo feeding the 3".
 
O2 sensors still attached? Mike

Yep brand new O2 sensors from toyota of Dallas no codes yet no strong exhaust smell. Really I cant tell that much difference a lil more pep but not much. Best thing is no hot passenger floor board for the :princess:. Ill find out about MPG on the Colorado trip next week.
 
Just FYI I did not get the high flow cat in time to install it for the Colorado trip. Ive put a little over 3000 miles on it now highway and trail no codes. I averaged 11.3MPG on the trip trail and highway per the scanguage. I weighed the cruiser when I left it was 7,860lbs and the trailer was 1,920lbs for a grand total of 9,780lbs. I cant tell if power was more or less because I had the trailer attached the whole time. I also knocked a approximately 2 inch square hole in the muffler at the start of the trip. But no codes.
 
Back
Top Bottom