electrical gurus, how do i do this?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 7, 2007
Threads
83
Messages
500
Location
Raccoon City
Website
www.coopxgear.com
ok, so for all of the electrical gurus here on mud. I have been collecting various bits to install blackout markers and lights on my cruiser. My question is how can i install a switch (preferably something made by Mr T and adapted to work) that will allow me to kill the headlights, signals, flashers, brakes, and interior lights while still running my blackouts? I don't want to have to run the gigantic unit thats used in a HMMWV but don't remember how it was done is the older CUCV.
 
Beard -

I guess this would be serious work. You would need to wire all of the lights (headlights, signals, falshers, brakes, interior, etc.) to your new switch and that would act as a "breaker". I would do it by running all the wire from the output (actual lights) and then to a circuit connected to the switch...that would avoid some of the trouble of digging in and finding the source. Just my non-technical-electrical thoughts.

Cheers.

- Mark
 
Well all lights are run to the dash/steering column so I would think it would be much easier tying in there.

edit: actually isn't there a headlight fuse?
 
once the point of this?
 
I was thinking source...because of interior lights, blinkers, and everything else...you would want to keep them fused but, have a master switch to cut everything. I think since Beard lives zombie movies he doesn't want to be seen when he is on the hunt...maybe I will send him an extra PVS-14...
 
duh, yeah Zombies! :flipoff2:

there's no reason to call it ruining a perfectly good electrical system if its done right. That's why i asked the electrical gurus here.
 
hehe, well come on! OBVIOUSLY I don't think that!!!!!

All bulbs are fused, so I would attack the solution from there. At least that is the easiest way I can see.
 
All bulbs are fused, so I would attack the solution from there. At least that is the easiest way I can see.

You'd need to track down the fuses/wires that go just to the running/headlights, and not to the console. I'm assuming you want to be able to turn off the exterior lights while maintaining your interior lights.


Actually, the 'cruiser is already wired for this.

There's already a dimmer setup for the interior (console) lights, but it does not effect the exterior lights. Find where the wire splits off from the switch on the column and goes to the dimmer, that's the control for your interior lights. The other one should be the control for your exterior lights. Wire a switch in there, and you can cut your exterior lights without effecting the interior lights.

I would wire your blackout lights completely seperate, with a seperate switch for them.
 
Can't you just turn the headlight switch off and wire up a switch to cut out the brake lights? Then your truck would have no lights at all. Then install your blackout lights to on their own circuit?
 
Can't you just turn the headlight switch off and wire up a switch to cut out the brake lights? Then your truck would have no lights at all. Then install your blackout lights to on their own circuit?


Turning the headlight switch off means that you have no dash lights. Can't see your speed, RPM, etc.


I would not ever recommend to someone to wire a switch to cut out the brake lights. If you ever get in an accident and have such a switch, that's easily grounds for a huge lawsuit.
 
Turning the headlight switch off means that you have no dash lights. Can't see your speed, RPM, etc.

True, I forgot that.


I would not ever recommend to someone to wire a switch to cut out the brake lights. If you ever get in an accident and have such a switch, that's easily grounds for a huge lawsuit.

It's not something I would do on my truck, but it was asked in the first post.
 
Back
Top Bottom