EGR replacement

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 21, 2004
Threads
129
Messages
1,575
Location
MN physically, MI spiritually
I got 71 code today for the second time this year. Last time I fixed it with a small BFH but I may need to caugh up for a new EGR.

Question is, for those who have done this before, have you replaced the studs as well as the gasket and the EGR or just the gasket and EGR. The FSM calls for removing he studs and replacing them for some reason. Is there really anything to this or have you guys just left these in and done the gasket and EGR?

Thanks for the help.
 
The studs must come out to remove the EGR,as the EGR pipe (being stiff) will not allow the EGR to come straight off the studs, therefore, the studs must come out to allow the EGR to come slightly forward away from the EGR pipe, once that it unscrewed from the backside of the EGR.

You must (should) replace the metal gasket as it has a small section that crushes as the new EGR is torqued down, ensuring a better seal. There is a compression ring on the EGR pipe, but they become sort of welded to the pipe, so pretty much impossible to pull the old one off to replace it, so don't. IMO.

If the studs are corroded badly (mine were), then it would be a good idea to replace them, also with new OEM type nuts. It may help to use some penetrating oil a couple of times, a couple of days before you attempt to remove the studs and the EGR from the EGR pipe.

g
 
I got 71 code today for the second time this year. Last time I fixed it with a small BFH but I may need to caugh up for a new EGR.

Code 71 does not necessarily mean you have a bad EGR valve. You need to do the diagnostics as listed in the FSM and isolate the problem. Your problem could be clogged or leaking vacuum lines.

-B-
 
The studs must come out to remove the EGR,as the EGR pipe (being stiff) will not allow the EGR to come straight off the studs, therefore, the studs must come out to allow the EGR to come slightly forward away from the EGR pipe, once that it unscrewed from the backside of the EGR.

You must (should) replace the metal gasket as it has a small section that crushes as the new EGR is torqued down, ensuring a better seal. There is a compression ring on the EGR pipe, but they become sort of welded to the pipe, so pretty much impossible to pull the old one off to replace it, so don't. IMO.

If the studs are corroded badly (mine were), then it would be a good idea to replace them, also with new OEM type nuts. It may help to use some penetrating oil a couple of times, a couple of days before you attempt to remove the studs and the EGR from the EGR pipe.

g

Fantastic! Thanks for the info!

Code 71 does not necessarily mean you have a bad EGR valve. You need to do the diagnostics as listed in the FSM and isolate the problem. Your problem could be clogged or leaking vacuum lines.

-B-

Thanks Beo, I have done almost everything in the FSM and I am slowly narrowing the problen down to the EGR being clogged or defunct. Thanks for the input and I will, for sure, check everything before I go for the EGR.

Photogod,

What's a BFH? I've got a code 71 as well. Thanks

allian, the BFH is a Big F#*king Hammer. Although I used a small one so as not to destroy the working parts. I did an easy, tap, tap, tap to loosen things up i bit. :cheers:
 
The PO of my truck had the EGR valve replaced at a dealership, and they replaced two gaskets, as well as the valve and 2 nuts.

If it helps, the p/n for the EGR valve is 25620-66011, and the gaskets are 25627-66010 and 25628-66010 (one of each)
 
I got 71 code today for the second time this year. Last time I fixed it with a small BFH but I may need to caugh up for a new EGR.

Question is, for those who have done this before, have you replaced the studs as well as the gasket and the EGR or just the gasket and EGR. The FSM calls for removing he studs and replacing them for some reason. Is there really anything to this or have you guys just left these in and done the gasket and EGR?

Thanks for the help.

I reused the studs and put on a new gasket. You have to remove the studs to get the EGR valve off. I can't remember, but I think that it is threaded through the valve and into the TB.

An easier thing to try first is to clean the modulator and replace/clean all the vacuum hoses. Be sure to clear out any vacuum line intakes too.
 
I reused the studs and put on a new gasket. You have to remove the studs to get the EGR valve off. I can't remember, but I think that it is threaded through the valve and into the TB.

An easier thing to try first is to clean the modulator and replace/clean all the vacuum hoses. Be sure to clear out any vacuum line intakes too.

I took all of the vacume lines off and blew them out. Cleaned the modulator and have done all the tests except the VSV check and that is a last resort because I don't want to remove the intake yet.

Last time I used the BFH on the EGR valve it fixed the problem for quite a while.
 
I took all of the vacume lines off and blew them out. Cleaned the modulator and have done all the tests except the VSV check and that is a last resort because I don't want to remove the intake yet.

Last time I used the BFH on the EGR valve it fixed the problem for quite a while.


When I went code 71 I went overkill. I replaced the modulator and the EGR valve. I cleaned the temp sensor and all the small vacuum lines. The big one off the EGR valve I cleaned with degreaser and a pipe cleaner. I also reamed all the vacuum line ports. So far I haven't had a single problem in 18 months and 10K miles. I have no clue what cured my EGR system, but I do remember when I blew through my old dirty modulator it felt like some sort of blockage was blown out. At some point I guess it doesn't really matter, but I would start simple cleaning or better replacing all the vacuum lines and then work through diagnosing the modulator, VSV, EGR valve and temp sensor. Your previous SFH fix on the EGR valve is interesting and may point in that direction though.

I avoided the VSV testing as I didn't want to remove the intake. However, there are a number of posts on removing it without removing the intake. It is reported that you can remove it in less than 20 minutes this way. I haven't had to try that method out yet though.

Good luck.
 
I find the method of opening gas cap after I get the CEL for the EGR code will turn the light off after a few a couple of starts / driving around town.

Note: Cleaning the EGR is on list of things to do but only for summer :D
 
I find the method of opening gas cap after I get the CEL for the EGR code will turn the light off after a few a couple of starts / driving around town.

What code are you getting? The EGR system is not connected to the fuel supply system.
-B-
 
What code are you getting? The EGR system is not connected to the fuel supply system.
-B-

The imfamous code 71.

What I have notice is that if I get the CEL for 71. Letting the gas cap pressure out (open gas cap and re tighten)and then just drive the CEL turns off as I drive. If I ignore it the light stays on for a very long time or until I let the TLC sit for awhile and drive.

Some older EGR systems did burned unused fuel ... no idea if this is the case for the 94 TLC.
 
Your Evap system burns unused fuel, not your EGR system. The EGR system circulates exhaust gas to cool down the combustion chamber. I have not reviewed the '94 FSM but I do not believe these 2 systems have anything in common other than the ECM. You are either getting multiple codes, different codes, or something.

-B-
 
Last edited:
I find the method of opening gas cap after I get the CEL for the EGR code will turn the light off after a few a couple of starts / driving around town.

Note: Cleaning the EGR is on list of things to do but only for summer :D

That's interesting because I filled up a few days ago while the rig was running and the next day I had the EGR code. Gremlins in the system!

Looking at the FSM there is a correlation between the VSV in the Evap system and the VCV in the EGR system in that they are connected. The charcoal canister connects directly to the VCV which connects from a secondary tube to the VSV which goes directly to the EGR valve and the vacume modulator. There fore they are related in some fashion.

Maybe a loss of pressure in the gas tank caused the EGR code?
 
Last edited:
That's interesting because I filled up a few days ago while the rig was running and the next day I had the EGR code. Gremlins in the system!

Looking at the FSM there is a correlation between the VSV in the Evap system and the VCV in the EGR system in that they are connected. The charcoal canister connects directly to the VCV which connects from a secondary tube to the VSV which goes directly to the EGR valve and the vacume modulator. There fore they are related in some fashion.

Maybe a loss of pressure in the gas tank caused the EGR code?

Funny you say that; I see code 71 more often with a full tank and 1/8 of tank more often.

Well, I think of too much pressure and it's not venting. The reasoning is if I see the CEL, if I stop and open the gas cap (you'll hear the hiss) and then Go back driving the CEL goes away after driving a bit. If I do nothing it will be the next day that I see the CEL light turn off.

As for the charcoal canister I thought the same thing too... I read lots on the forum and in the end kinda gave up when there was talk about the RED/GREEN EGR module replacement. Since I don't see that the TLC is in limp mode I have just ignored it and gone to PM instead and have this listed as todo list.
 
Looking at the FSM there is a correlation between the VSV in the Evap system and the VCV in the EGR system in that they are connected. The charcoal canister connects directly to the VCV which connects from a secondary tube to the VSV which goes directly to the EGR valve and the vacume modulator. There fore they are related in some fashion.

Can you scan that page and post it please?

-B-
 
You folks noting a connection of a CEL and fuel cap should check the black vacuum line from the charcoal canister to the blue EVAP VSV (looks like EGR VSV which is 4" behind it). On my 93 and my bro in law's 93 there are a couple hoses there that come off once in a while. They pop right back on in seconds - easy access, so check them.

Also, Photogod you can take your EGR VSV off the intake manifold in about 15 minutes if you have 30" of extensions and reasonably sized hands.

Remove lower bolt on intake manifold black brace. Then upper. Lay under truck and remove two bolts holding EGR VSV on. Leave bolts slightly in place - helps with pulling VSV's vacuum lines with having something to pull against in there from above. Then remove bolts all the way by hand. With the intake brace out of the way, it's not as tough to reach the VSV. I think this "no intake removal" is posted here by someone already, which I did not know until I managed to figure it out in the garage.

DougM
 
Back
Top Bottom