dual battery tray coating

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 28, 2004
Threads
109
Messages
440
Location
Medford, Oregon
I'm finishing up a dual battery tray and now I'm wondering how to coat for durability. rubberized coating, powder coating or paint, chrome is for :princess: . I want it to last but don't know which way to go. What have you all done, if anything.
 
Actually I POR 15'd mine and it has held up really well. It only likes to stick to sandblasted or etched metal. If you can't sandblast it, use some 3M metal prep which is phosphoric and hydrochloric acid, scrub it with a scotchbrite let it sit a fet minutes and keep it wet with the solution, then rinse with water and it will air dry to a golden rust color. That should allow the POR to stick just fine.
Post a pic of your new tray!!!!

Ed
 
I used some spray bedliner like stuff, think it was the Duplicolor stuff, worked great
 
Those are both great ideas. Heres a few pix. It still needs a few brackets and a mount for the isolator. I will finish this weekend, as long as my wife will let me get in the shop.
 
Last edited:
I used rustbullet with a POR topcoat.
 
Nice work, something that pretty is worthy of powder coating. There is an outfit in town that does really good work-Scala? Of course you have lots of time to paint it yourself.. If you do end up wanting to sandblast I can do that for you. A good primer and paint followed up with that roll-on rubberized liner stuff or take it down and have them shoot it while they do a bed. If you are running the optima's you barely need to worry about the old rust & rought factor.;)
So were all the neighbors looking out their windows wondering what you are doing?
 
Hey Kief, I think I'm going to go with the bedliner stuff. I'm going to use those 2 red tops I had in the garage. The older gentleman from a few houses down came over and wanted to know what I was doing to "the jeep" :doh: I nicely corrected him. I'm going to attempt to wire the duals this weekend. Talk with later, Greg
 
secretagent said:
Hey Kief, I think I'm going to go with the bedliner stuff. I'm going to use those 2 red tops I had in the garage. The older gentleman from a few houses down came over and wanted to know what I was doing to "the jeep" :doh: I nicely corrected him. I'm going to attempt to wire the duals this weekend. Talk with later, Greg

Think twice about the bedliner stuff - specifically the spraycan "Duraliner" available everywhere. It is sensitive to oils and will bubble up and detach it's grip if exposed directly. I have it on both bumpers of one of my Dodges where it's better than paint but still not as tough as any of the commercial bedliner products. but when I used it in a box in the bed where I put chainsaw oil (not fuel) it didn't last for a month.

I'd do POR-15 despite the more difficult application. Even though the redtops won't gas up and produce the corrosive acids that conventional batteries do. anything flying around in your engine compartment could end up spoiling the job.
 
I do a lot of hobby gunsmithing, and there are spray and bake lacquers that are incredibly tough and provide excellent protection, as well as spray on epoxies.

Better than bedliner for this application, IMHO.

PM for details.

Kirk
 
I used a good prep and Zero-Rust. If you are using sealed gel batteries your only enemy will be wearing down to metal and potential rust. I have a plate style tray so I cut up a rubber car mat and set the batteries on top of that to keep from rubbing the paint off.

Best durability would be to powder coat, line-x or rhino line the thing. guess you could ge the herculiner and do it yourself.

Nice tray by the way:D
 
Back
Top Bottom